View IMX27_4592011.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

i.MX27 and i.MX27L
i.MX27 and i.MX27L Data Sheet
Multimedia Applications Processor 1 Introduction
1.
Package Information Plastic Package Case 1816-01 (MAPBGA-404) Case 1931-04 (MAPBGA-473) Ordering Information See Table 1 on page 4 for ordering information.
The i.MX27 and i.MX27L (MCIMX27/MX27L) Multimedia Applications Processors represents the next step in low-power, high-performance application processors. Unless otherwise specified, the material in this data sheet is applicable to both the i.MX27 and i.MX27L processors and referred to singularly throughout this document as i.MX27. The i.MX27L does not include the following features: ATA-6 HDD Interface, Memory Stick Pro, VPU: MPEG-4/ H.263/H.264 HW encoder/decoder, and eMMA (PrP processing, CSC, deblock, dering). Based on an ARM926EJ-STM microprocessor core, the i.MX27/27L processor provides the performance with low-power consumption required by modern digital devices such as the following: * Feature-rich cellular phones * Portable media players and mobile gaming machines * Personal digital assistants (PDAs) and wireless PDAs
2.
3.
5.
6. 7.
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2. Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.3. Ordering Information . . . . . . . . . . . . . . . . . . . . . . 4 Functional Description and Application Information . . . . 4 2.1. ARM926 Microprocessor Core Platform . . . . . . . . 4 2.2. Module Inventory . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.3. Module Descriptions . . . . . . . . . . . . . . . . . . . . . . . 9 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 3.1. Power-Up Sequence . . . . . . . . . . . . . . . . . . . . . . 35 3.2. EMI Pins Multiplexing . . . . . . . . . . . . . . . . . . . . . 36 4. Electrical Characteristics . . . . . . . . . . . . . . . . . . 40 4.1. i.MX27/IMX27L Chip-Level Conditions . . . . . . . . 40 4.2. Module-Level Electrical Specifications . . . . . . . . 43 4.3. Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . 54 Package Information and Pinout . . . . . . . . . . . . . . . . 105 5.1. Full Package Outline Drawing (17 mm x 17 mm) 105 5.2. Pin Assignments (17 mm x 17 mm) . . . . . . . . . 106 5.3. Full Package Outline Drawing (19 mm x 19 mm) 125 5.4. Pin Assignments (19 mm x 19 mm) . . . . . . . . . 126 Product Documentation . . . . . . . . . . . . . . . . . . . . . . . 147 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
This document contains information on a new product. Specifications and information herein are subject to change without notice.
(c) Freescale Semiconductor, Inc., 2007, 2009. All rights reserved.
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Freescale Semiconductor Data Sheet, Technical Data
Document Number: MCIMX27EC Rev. 1.5, 12/2009
Introduction
* *
Portable DVD players Digital cameras
The i.MX27/MX27L processor features the advanced and power-efficient ARM926EJ-S core operating at speeds up to 400 MHz, and is optimized for minimal power consumption using the most advanced techniques for power saving (for example, DPTC, power gating, and clock gating). With 90 nm technology and dual Vt, the i.MX27/MX27L device provides the optimal performance vs. leakage current balance. The performance of the i.MX27/MX27L processors are both boosted by an on-chip cache system, and features peripheral devices, such as an MPEG-4, H.263, an H.264 video codec (up to D1--720 x 486--@ 30 FPS), LCD, eMMA_lt, and CMOS Sensor Interface controllers. The i.MX27/MX27L processors supports connections to various types of external memories, such as 266-MHz DDR, NAND Flash, NOR Flash, SDRAM, and SRAM. The i.MX27/MX27L devices can be connected to a variety of external devices using technology, such as high-speed USBOTG 2.0, the Advanced Technology Attachment (ATA), Multimedia/Secure Data (MMC/SDIO), and CompactFlash. NOTE The i.MX27L does not support the ATA-6 HDD interface.
1.1
Features
The MX27/MX27L processors are targeted for video and voice over-IP (V2IP) and smart remote controllers. It also provides low-power solutions for any high-performance and demanding multimedia and graphics applications. The systems include the following features: * Multi-standard video codec (i.MX27 only) -- MPEG-4 part-II simple profile encoding/decoding -- H.264/AVC baseline profile encoding/decoding -- H.263 P3 encoding/decoding -- Multi-party call: one stream encoding and two streams decoding simultaneously -- Multi-format: encodes MPEG-4 bitstream, and decodes H.264 bitstream simultaneously -- On-the-fly video processing that reduces system memory load (for example, the power-efficient viewfinder application with no involvement of either the memory system or the ARM CPU) * Advanced power management (i.MX27/27L) -- Dynamic process and temperature compensation -- Multiple clock and power domains -- Independent gating of power domains * Multiple communication and expansion ports
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 2 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Introduction
1.2
Block Diagram
Figure 1 shows the i.MX27 simplified interface block diagram.
DDR/ SDRAM NOR/NAND Flash LCD Display Camera
M3IF SDRAMC NFC WEIM PCMCIA/CF
LCDC SLCDC CSI ARM926 Platform
AP Peripherals AUDMUX SSI (2) CSPI (3) I2C (2) UART (6) USBOTG HS 1-Wire FEC ATA SDHC (3) MSHC GPIO JTAG CRM PWM KPP
ARM926EJ-S
L1 I/D cache
AHB Switch Fabric
VRAM
AITC ETM9 eMMA-lt
iROM 10/100 ETH XVR
Security SAHARA2 RTIC SCC IIM
Video Codec DMA
Timers WDOG GPT (6) RTC
Application Processor Domain (AP)
Bluetooth
Note: The i.MX27L does not support the following: * ATA-6 HDD Interface * Memory Stick Pro * VPU: MPEG-4/.263/H.264 HW encoder/decoder * eMMA (PrP processing, CSC, deblock, dering)
WLAN
USBOTG XVR
MMC/SDIO
Keypad
Access Conn.
Figure 1. i.MX27/MX27L Simplified Interface Block Diagram
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 3
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Audio/Power Management JTAG IrDA XVR
Functional Description and Application Information
1.3
Ordering Information
Table 1. Ordering Information1
Device MCIMX27VOP4A! MCIMX27LVOP4A! MCIMX27MOP4A! MCIMX27LMOP4A! MCIMX27VJP4A MCIMX27LVJP4A MCIMX27MJP4A MCIMX27LMJP4A
1
Table 1 provides ordering information for the MAPBGA, lead-free packages.
Temperature -20 C to +85 C -20 C to +85 C -40 C to +85 C -40 C to +85 C -20 C to +85 C -20 C to +85 C -40 C to +85 C -40 C to +85 C
Package 1816-01 1816-01 1931-04 1931-04 1816-01 1816-01 1931-04 1931-04
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: Indicated by the Icon (!)
2
2.1
Functional Description and Application Information
ARM926 Microprocessor Core Platform
The ARM926 Platform consists of the ARM926EJ-S processor, ETM9, ETB9, a 6 x 3 Multi-Layer AHB crossbar switch (MAX), and a "primary AHB" complex. * The instruction bus (I-AHB) of the ARM926EJ-S processor is connected directly to MAX Master Port 0. * The data bus (D-AHB) of the ARM926EJ-S processor is connected directly to MAX Master Port 1. Four alternate bus master interfaces are connected to MAX Master Ports 2-5. Three slave ports of the MAX are AHB-Lite compliant buses. Slave Port 0 is designated as the "primary" AHB. The primary AHB is internal to the platform and has five slaves connected to it: the AITC interrupt module, the MCTL memory controller, and two AIPI peripheral interface gaskets. Slave Ports 1 and 2 of the MAX are referred to as "secondary" AHBs. Each of the secondary AHB interfaces is only accessible off platform. The ARM926EJ-S processor supports the 32-bit and 16-bit ARM Thumb instruction sets, enabling the user to trade off between high performance and high-code density. The ARM926EJ-S processor includes features for efficient execution of Java byte codes, providing Java performance similar to the just-in-time (JIT) compiler--which is a type of Java compiler--but without the associated code overhead. The ARM926EJ-S processor supports the ARM debug architecture and includes logic to assist in both hardware and software debugging. The ARM926EJ-S processor has a Harvard cached architecture and provides a complete high-performance processor subsystem, including the following: * An ARM9EJ-S integer core * A Memory Management Unit (MMU)
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 4 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
* *
Separate instruction and data AMBA AHB bus interfaces ETM and JTAG-based debug support
The ARM926EJ-S processor provides support for external coprocessors enabling floating-point or other application-specific hardware acceleration to be added. The ARM926EJ-S processor implements ARM architecture version 5TEJ. The four alternate bus master ports on the ARM926 Platform, which are connected directly to master ports of the MAX, are designed to support connections to multiple AHB masters external to the platform. An external arbitration AHB control module is needed if multiple external masters are desired to share an ARM926 Platform alternate bus master port. However, the alternate bus master ports on the platform support seamless connection to a single master with no external interface logic required. A primary AHB MUX (PAHBMUX) module performs address decoding, read data muxing, bus watchdog, and other miscellaneous functions for the primary AHB within the platform. A clock control module (CLKCTL) is provided to support a power-conscious design methodology, as well as implementation of several clock synchronization circuits.
2.1.1
Memory System
The ARM926EJ-S complex includes 16-Kbyte Instruction and 16-Kbyte Data caches. The embedded 45-Kbyte SRAM (VRAM) can be used to avoid external memory accesses or it can be used for applications. There is also a 24-Kbyte ROM for bootstrap code.
2.2
Module Inventory
Table 2 shows an alphabetical listing of the modules in the i.MX27/MX27L multimedia applications processors. A cross-reference to each module's section and page number goes directly to a more detailed module description for additional information.
Table 2. Digital and Analog Modules
Block Mnemonic 1-Wire(R) Block Name 1-Wire Interface Functional Grouping Connectivity Peripheral Brief Description The 1-Wire module provides bi-directional communication between the ARM926EJ-S and the Add-Only-Memory EPROM (DS2502). The 1-Kbit EPROM is used to hold information about battery and communicates with the ARM926 Platform using the IP interface. The AIPI acts as an interface between the ARM Advanced High-performance Bus Lite. (AHB-Lite) and lower bandwidth peripherals that conforms to the IP Bus specification, Rev 2.0. AITC is connected to the primary AHB as a slave device. It generates the normal and fast interrupts to the ARM926EJ-S processor. The ARM926EJ-S (ARM926) is a member of the ARM9 family of general-purpose microprocessors targeted at multi-tasking applications. Section/ Page 2.3.1/9
AIPI
AHB-Lite IP Interface Module ARM9EJ-S Interrupt Controller ARM926EJ-S
Bus Control
2.3.2/10
AITC
Bus Control
2.3.3/10
ARM926EJS
CPU
2.3.4/10
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 5
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
Table 2. Digital and Analog Modules (continued)
Block Mnemonic ATA Block Name Advanced Technology(AT) Attachment Digital Audio Multiplexer Clock and Reset Module CMOS Sensor Interface Configurable Serial Peripheral Interface (x3) Functional Grouping Connectivity Peripheral Multimedia Peripheral Brief Description The ATA block is an AT attachment host interface. It interfaces with IDE hard disc drives and ATAPI optical disc drives. The AUDMUX interconnections allow multiple, simultaneous audio/voice/data flows between the ports in point-to-point or point-to-multipoint configurations. Section/ Page 2.3.5/11
AUDMUX
2.3.6/11
CRM
Clock and The CRM generates clock and reset signals used throughout Reset Control the i.MX27/MX27L processors and also for external peripherals. Multimedia Interface Connectivity Peripheral The CSI is a logic interface which enables the i.MX27/MX27L processors to connect directly to external CMOS sensors and a CCIR656 video source. The i.MX27/MX27L processors have three CSPI modules. CSPI is equipped with two data FIFOs and is a master/slave configurable serial peripheral interface module, allowing the i.MX27/MX27L processors to interface with both external SPI master and slave devices.
2.3.7/12
CSI
2.3.8/12
CSPI
2.3.9/13
DMAC
Direct Memory Access Controller eMMA_lt
Standard System Resource H/W Accelerator Functions
2.3.10/13 The DMAC of the i.MX27/MX27L processors provides 16 channels supporting linear memory, 2D memory, FIFO and end-of-burst enable FIFO transfers to support a wide variety of DMA operations. eMMA_lt consists of a PreProcessor and PostProcessor, and provides video acceleration. The PrP and PP can be used for generic video pre and post processing such as scaling, resizing, and color space conversions. 2.3.11/13
eMMA_lt
EMI
External Memory Interface
Memory The EMI includes Interface (EMI) * Multi-Master Memory Interface (M3IF) * Enhanced SDRAM/MDDR memory controller (ESDRAMC) * PCMCIA memory controller (PCMCIA) * NAND Flash Controller (NFC) * Wireless External Interface Module (WEIM) External Memory Interface Connectivity Peripheral
--
ESDRAMC
Enhanced SDRAM Controller Fast Ethernet Controller
The ESDRAMC provides interface and control for synchronous 2.3.12/15 DRAM memories for the system. The FEC performs the full set of IEEE 802.3/Ethernet CSMA/CD media access control and channel interface functions. The FEC supports connection and functionality for the 10/100 Mbps 802.3 media independent interface (MII). It requires an external transceiver (PHY) to complete the interface to the media. The GPIO provides 32 bits of bidirectional, general purpose I/O. This peripheral provides dedicated general-purpose pins that can be configured as either inputs or outputs. 2.3.13/15
FEC
GPIO
General Purpose I/O Module General Purpose Timer
Pins
2.3.14/16
GPT
Timer Peripheral
The GPT is a multipurpose module used to measure intervals 2.3.15/16 or generate periodic output.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 6 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
Table 2. Digital and Analog Modules (continued)
Block Mnemonic I2C Block Name Inter IC Communication IC Identification Module Functional Grouping Connectivity Peripheral Security Brief Description Section/ Page
The I2C provides serial interface to control the sensor interface 2.3.16/17 and other external devices. Data rates of up to 100 Kbits/s are supported. The IIM provides an interface for reading--and in some cases, 2.3.17/17 programming, and overriding identification and control information stored in on-chip fuse elements. Contact your Freescale Semiconductor sales office or distributor for additional information on SCC, RTIC, IIM, SAHARA2 The JTAGC provides debug access to the ARM926 core, built-in self-test (BIST), and boundary scan test control. The KPP is used for key pad matrix scanning or as a general purpose I/O. This peripheral simplifies the software task of scanning a keypad matrix. The LCDC provides display data for external gray-scale or color LCD panels. The M3IF controls memory accesses from one or more masters through different port interfaces to different external memory controllers ESDCTL/MDDRC, PCMCIA, NFC, and WEIM. 2.3.18/17 2.3.19/17
IIM
JTAGC KPP
JTAG Controller Keypad Port
Debug Connectivity Peripheral Multimedia Interface External Memory Interface Bus Control
LCDC
Liquid Crystal Display Controller Multi-Master Memory Interface Multi-layer AHB Crossbar Switch
2.3.20/17
M3IF
2.3.21/18
MAX
The ARM926EJ-S processor's instruction and data buses and 2.3.22/18 all alternate bus master interfaces arbitrate for resources via a 6 x 3 MAX. There are six fully functional master ports (M0-M5) and three fully functional slave ports (S0-S2). The MAX is uni-directional. All master and slave ports are AHB-Lite compliant. The MSHC is placed in between the AIPI and the customer memory stick to support data transfer from the i.MX27 device to the customer memory stick. Note: The i.MX27L does not support the MSHC feature The NFC is a submodule of EMI. The NFC implements the interface to standard NAND Flash memory devices. The PCMCIA host adapter module provides the control logic for PCMCIA socket interfaces, and requires some additional external analog power switching logic and buffering. 2.3.23/19
MSHC
Memory Stick Host Controller
Connectivity Peripheral
NFC
NAND Flash Controller Personal Computer Memory Card International Association Phase Lock Loop Pulse-Width Modulator
External Memory Interface External Memory Interface
2.3.24/19
PCMCIA
2.3.25/20
PLL
Clock and The two DPLLs provide clock generation in digital and mixed Reset Control analog/digital chips designed for wireless communication and other applications. Timer Peripheral The PWM has a 16-bit counter and is optimized to generate sound from stored sample audio images. It can also generate tones.
2.3.26/20
PWM
2.3.27/20
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 7
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
Table 2. Digital and Analog Modules (continued)
Block Mnemonic RTC Block Name Real Time Clock Functional Grouping Timer Peripheral Brief Description The RTC module provides a current stamp of seconds, minutes, hours, and days. Alarm and timer functions are also available for programming. The RTC supports dates from the year 1980 to 2050. Section/ Page 2.3.28/20
RTIC
Run-Time Integrity Checkers
Security
The RTIC ensures the integrity of the contents of the peripheral 2.3.29/21 memory and assists with boot authentication. Contact your Freescale Semiconductor sales office or distributor for additional information on SCC, RTIC, IIM, SAHARA2 SAHARA2 is a security co-processor which forms part of the 2.3.30/21 Platform Independent Security Architecture (PISA), and can be used on cell phone baseband processors or wireless PDAs. Contact your Freescale Semiconductor sales office or distributor for additional information on SCC, RTIC, IIM, SAHARA2 The SCC is a hardware component composed of two blocks--the Secure RAM module, and the Security Monitor. The Secure RAM provides a way of securely storing sensitive information. The Security Monitor implements the security policy, checking algorithm sequencing, and controlling the Secure State. Contact your Freescale Semiconductor sales office or distributor for additional information on SCC, RTIC, IIM, SAHARA2 2.3.31/21
SAHARA2
Symmetric/ Asymmetric Hashing and Random Accelerator
Security
SCC
Security Controller Module
Security
SDHC
Secured Digital Host Controller Smart Liquid Crystal Display Controller Synchronous Serial Interface
Connectivity Peripheral Multimedia Interface Multimedia Peripheral
The SDHC controls the MMC (MultiMediaCard), SD (Secure 2.3.32/21 Digital) memory, and I/O cards by sending commands to cards and performing data accesses to and from the cards. The SLCDC module transfers data from the display memory buffer to the external display device. 2.3.33/22
SLCDC
SSI
The SSI is a full-duplex, serial port that allows the chip to 2.3.34/22 communicate with a variety of serial devices, such as standard codecs, digital signal processors (DSPs), microprocessors, peripherals, and popular industry audio codecs that implement the inter-IC sound bus standard (I2S) and Intel AC97 standard. 2.3.35/23 The UART provides serial communication capability with external devices through an RS-232 cable or through use of external circuitry that converts infrared signals to electrical signals (for reception) or transforms electrical signals to signals that drive an infrared LED (for transmission) to provide low speed IrDA compatibility.
UART
Universal Asynchronous Receiver/ Transmitter
Connectivity Peripheral
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 8 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
Table 2. Digital and Analog Modules (continued)
Block Mnemonic USB Block Name Universal Serial Bus-2 Host Controllers and 1 OTG (On-The-Go) Functional Grouping Connectivity Peripherals Brief Description Section/ Page
2.3.36/23 The i.MX27/MX27L processors provide two USB Host controllers and one USBOTG of which: * USB Host 1 is designed to support transceiverless connection to the on-board peripherals in Low Speed and Full Speed mode, and connection to the ULPI (UTMI+Low-Pin Court) and Legacy Full Speed transceivers * USB Host 2 is designed to support transceiverless connection to the Cellular Modem Baseband Processor * The USBOTG controller offers HS/FS/LS capabilities in Host mode and HS/FS in device mode. In Host mode, the controller supports direct connection of a FS/LS device (without external hub). In device (bypass) mode, the OTG port functions as gateway between the Host 1 Port and the OTG transceiver. Video Codec module supports full duplex video codec with 25 2.3.39/25 fps VGA image resolution, integrates H.264 BP, MPEG-4 SP and H.263 P3 video processing standard together. 2.3.37/24 The WDOG module protects against system failures by providing a method for the system to recover from unexpected events or programming errors. The Wireless External Module (WEIM) handles the interface to 2.3.38/25 devices external to chip, including generation of chip selects, clock and control for external peripherals and memory. It provides asynchronous and synchronous access to devices with SRAM-like interface.
Video Codec
Video Codec
Hardware Acceleration Timer Peripheral External Memory Interface
WDOG
Watchdog Timer Module Wireless External Interface Module
WEIM
2.3
Module Descriptions
This section provides a brief text description of all the modules included in the i.MX27/MX27L devices, arranged in alphabetical order.
2.3.1
1-Wire Module
The 1-Wire module provides bi-directional communication between the ARM926 core and the Add-Only Memory EPROM, DS2502. The 1-Kbit EPROM holds information about the battery and communicates with the ARM926 Platform using the IP interface. Through the 1-Wire interface, the ARM926 acts as the bus master while the DS2502 device is the slave. The 1-Wire peripheral does not trigger interrupts; hence it is necessary for the ARM926 to poll the 1-Wire to manage the module. The 1-Wire uses an external pin to connect to the DS2502. Timing requirements are met in hardware with the help of a 1 MHz clock. The clock divider generates a 1 MHz clock that is used as a time reference by the state machine. Timing requirements are crucial for proper operation, and the 1-Wire state machine and the internal clock provide the necessary signal. The clock must be configured to approximately 1 MHz. You can then set the 1-Wire register to send and receive bits over the 1-Wire bus.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 9
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
2.3.2
AHB-Lite IP Interface Module (AIPI)
The AIPI acts as an interface between the ARM Advanced High-performance Bus Lite. (AHB-Lite) and lower bandwidth peripherals conforming to the IP bus specification Rev 2.0. There are two AIPI modules in i.MX27/MX27L processors. The following list summarizes the key features of the AIPI: * All peripheral read transactions require a minimum of two system clocks (R-AHB side) and all write transactions require a minimum of three system clocks (R-AHB side). * The AIPI supports 8-bit, 16-bit, and 32-bit IP bus peripherals. Byte, half word, and full word reads and writes are supported. * The AIPI supports multi-cycle accesses by providing 16-bit to 8-bit peripherals operations and 32-bit to both 16-bit and 8-bit peripherals operations. * The AIPI supports 31 external IP bus peripherals each with a 4-Kbyte memory map (a slot).
2.3.3
ARM926EJ-S Interrupt Controller (AITC)
The ARM926EJ-S Interrupt Controller (AITC) is a 32-bit peripheral that collects interrupt requests from up to 64 sources and provides an interface to the ARM926EJ-S core. The AITC includes software controlled priority levels for normal interrupts. The AITC performs the following functions: * Supports up to 64 interrupt sources * Supports fast and normal interrupts * Selects normal or fast interrupt request for any interrupt source * Indicates pending interrupt sources via a register for normal and fast interrupts * Indicates highest priority interrupt number via register. (Can be used as a table index.) * Independently can enable or disable any interrupt source * Provides a mechanism for software to schedule an interrupt * Supports up to 16 software controlled priority levels for normal interrupts and priority masking * Can single-bit disable all normal interrupts and all fast interrupts. (Used in enabling of secure operations.)
2.3.4
ARM926EJ-S Platform
The ARM926EJ-S (ARM926) is a member of the ARM9 family of general-purpose microprocessors targeted at multi-tasking applications. The ARM926 supports the 32-bit ARM and 16-bit Thumb instructions sets. The ARM926 includes features for efficient execution of Java byte codes. A JTAG port is provided to support the ARM Debug Architecture, along with associated signals to support the ETM9 real-time trace module. The ARM926EJ-S is a Harvard cached architecture including an ARM9EJ-S integer core, a Memory Management Unit (MMU), separate instruction and data AMBA AHB interfaces, separate instruction and data caches, and separate instruction and data tightly coupled memory (TCM) interfaces. The ARM926 co-processor, instruction TCM, and data TCM interfaces will be tied off within the ARM926 Platform and will not be available for external connection.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 10 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
The ARM926EJ-S processor is a fully synthesizable macrocell, with a configurable memory system. Both instruction and data caches will be 16 kbytes on the platform. The cache is virtually accessed and virtually tagged. The data cached has physical tags as well. The MMU provides virtual memory facilities which are required to support various platform operating systems such as Symbian OS, Windows CE, and Linux. The MMU contains eight fully associative TLB entries for lockdown and 64 set associative entries. Refer to the ARM926EJ-S Technical Reference Manual for more information.
2.3.5
Advanced Technology Attachment (ATA)
The Advanced Technology Attachment (ATA) host controller complies with the ATA/ATAPI-6 specification. The primary use of the ATA host controller is to interface with IDE hard disc drives and Advanced Technology Attachment Packet Interface (ATAPI) optical disc drives. It interfaces with the ATA device over a number of ATA signals. This host controller supports interface protocols as specified in ATA/ATAPI-6 standard, as follows: * PIO mode 0, 1, 2, 3, and 4 * Multiword DMA mode 0, 1, and 2 * Ultra DMA modes 0, 1, 2, 3, and 4 with bus clock of 50 MHz or higher * Ultra DMA mode 5 with bus clock of 80 MHz or higher Before accessing the ATA bus, the host must program the timing parameters to be used on the ATA bus. The timing parameters control the timing on the ATA bus. Most timing parameters are programmable as a number of clock cycles (1 to 255). Some are implied. All of the ATA device-internal registers are visible to users, and they are defined as mirror registers in ATA host controller. As specified in ATA/ATAPI-6 standard, all the features/functions are implemented by reading/writing to the device's internal registers. There are basically two protocols that can be active at the same time on the ATA bus, as follows: * The first and simplest protocol (PIO mode access) can be started at any time by the ARM926 to the ATA bus. The PIO mode is a slow protocol, mainly intended to be used to program an ATA disc drive, but also can be used to transfer data to/from the disc drive. * The second protocol is the DMA mode access. DMA mode is started by the ATA interface after receiving a DMA request from the drive, and only if the ATA interface has been programmed to accept the DMA request. In DMA mode, either multiword-DMA or ultra-DMA protocol is used on the ATA bus. All transfers between FIFO and the host IP or DMA IP bus are zero wait states transfer, so a high-speed transfer between FIFO and DMA/host bus is possible.
2.3.6
Digital Audio MUX (AUDMUX)
The Digital Audio MUX (AUDMUX) provides programmable interconnecting for voice, audio, and synchronous data routing between host serial interfaces--for example, SSI, SAP, and peripheral serial interfaces--such as, audio and voice codecs. The AUDMUX allows audio system connectivity to be modified through programming, as opposed to altering the design of the system into which the chip is designed. The design of the AUDMUX allows multiple simultaneous audio/voice/data flows between the ports in point-to-point or point-to-multipoint configurations.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 11
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
Included in the AUDMUX are two types of interfaces. The internal ports connect to the processor serial interfaces, and the external ports connect to off-chip audio devices and serial interfaces of other processors. A desired connectivity is achieved by configuring the appropriate internal and external ports. The module includes full 6-wire SSI interfaces for asynchronous receive and transmit, as well as a configurable 4-wire (synchronous) or 6-wire (asynchronous) peripheral interface. The AUDMUX allows each host interface to be connected to any other host or peripheral interface in a point-to-point or point-to-multipoint (network mode).
2.3.7
Clock and Reset Module (CRM)
The Clock and Reset Module (CRM) generates clock and reset signals used throughout the i.MX27/MX27L processor and for external peripherals. It also enables system software to control, customize, or read the status of the following functions: * Chip ID * Multiplexing of I/O signals * I/O Driving Strength * I/O Pull Enable Control * Well-Bias Control * System boot mode selection * DPTC Control
2.3.8
CMOS Sensor Interface (CSI)
The CMOS Sensor Interface (CSI) is a logic interface that enables the i.MX27/MX27L processors to connect directly to external CMOS sensors and CCIR656 video source. The capabilities of the CSI include the following: * Configurable interface logic to support popular CMOS sensors in the market * Support traditional sensor timing interface * Support CCIR656 video interface, progressive mode for smart sensor, interlace mode for PAL and NTSC input * 8-bit input port for YCC, YUV, Bayer, or RGB data * 32 x 32 FIFO storing image data supporting Core data read and DMA data burst transfer to system memory * Full control of 8-bit and 16-bit data to 32-bit FIFO packing * Direct interface to eMMA-lt Pre-Processing block (PrP) - Not available on the i.MX27L * Single interrupt source to interrupt controller from maskable sensor interrupt sources: Start of Frame, End of Frame, Change of Field, FIFO full * Configurable master clock frequency output to sensor * Asynchronous input logic design. Sensor master clock can be driven by either the i.MX27/MX27L processor or by external clock source.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 12 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
*
Statistic data generation for Auto Exposure (AE) and Auto White Balance (AWB) control of the camera (for Bayer data only)
2.3.9
Configurable Serial Peripheral Interface (CSPI)
The Configurable Serial Peripheral Interface (CSPI) is used for fast data communication with fewer software interrupts. There are three CSPI modules in the i.MX27/MX27L processors, which provide a full-duplex synchronous serial interface, capable of interfacing to the SPI master and slave devices. CSPI1 and CSPI2 are master/slave configurable and include three chip selects to support multiple peripherals. CSPI3 is only a master and has one chip-select signal. The transfer continuation function of the CSPI enables unlimited length data transfers using 32-bit wide by 8-entry FIFO for both TX and RX data DMA support. The CSPI Ready (SPI_RDY) and Chip Select (SS) control signals enable fast data communication with fewer software interrupts. When the CSPI module is configured as a master, it uses a serial link to transfer data between the CSPI and an external device. A chip-enable signal and a clock signal are used to transfer data between these two devices. When the CSPI module is configured as a slave, the user can configure the CSPI Control register to match the external SPI master's timing.
2.3.10
Direct Memory Access Controller (DMAC)
The Direct Memory Access Controller (DMAC) provides 16 channels to support linear memory, 2D memory, FIFO, and end-of-burst enable FIFO transfers to support a wide variety of DMA operations. Features include the following: * Support of 16 channels linear memory, 2D memory, and FIFO for both source and destination * Support of 8-bit, 16-bit, or 32-bit FIFO port size and memory port size data transfer * Configurability of DMA burst length of up to a maximum of 16 words, 32 half-words, or 64 bytes for each channel * Bus utilization control for a channel that is not triggered by DMA request * Interrupts that are provided to interrupt handler on bulk data transfer complete or transfer error * DMA burst time-out error to terminate DMA cycle when the burst cannot be completed in a programmed timing period * Dedicated external DMA request and grant signal * Support of increment, decrement, and no increment for source and destination addressing * Support of DMA chaining
2.3.11
enhanced MultiMedia Accelerator Light (eMMA_lt)
The enhanced MultiMedia Accelerator Light (eMMA_lt) consists of the video pre-processor (PrP) and post-processor (PP). In contrast with i.MX21 processor's components, this eMMA does not include the video codec. A more powerful video codec is included as a separate module. NOTE The i.MX27L does not have a eMMA_lt module.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 13
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
Each module has individual control and configuration registers that are accessed via the IP interface, and are capable of bus mastering the AMBA bus to independently access system memory without any CPU intervention. This enables each module to be used independently of each other, and enables the pre-processor and post-processor modules to provide acceleration features for other software codec implementations and image processing software. These blocks work together to provide video acceleration, and to off-load the CPU from computation intensive tasks. The PrP and PP can be used for generic video pre- and post-processing, such as scaling, resizing, and color space conversions. A 32-bit-to-64-bit AHB gasket is used to convert a PrP AHB bus from a 32-bit to 64-bit protocol. A bypass function is implemented to bypass this 64-bit gasket if it is not needed. eMMA_lt supports the following image/video processing features: * Pre-processor: -- Data input: - System memory - Private DMA between CMOS Sensor Interface module and pre-processor -- Data input formats: - Arbitrarily formatted RGB pixels (16 or 32 bits) - YUV 4:2:2 (Pixel interleaved) - YUV 4:2:0 (IYUV, YV12) -- Input image size: 32 x 32 to 2044 x 2044 -- Image scaling: - Programmable independent CH-1 and CH-2 resizer. Can program to be in cascade or parallel. - Each resizer supports downscaling ratios from 1:1 to 8:1 in fractional steps. -- Channel-1 output data format - Channel 1 - RGB 16 and 32 bpp - YUV 4:2:2 (YUYV, YVYU, UYVY, VYUY) -- Channel-2 output data format - YUV 4:2:2 (YUYV) - YUV 4:4:4 - YUV 4:2:0 (IYUV, YV12) - RGB data and YUV data format can be generated concurrently -- 32/64-bit AHB bus * Post-processor -- Input data: - From system memory -- Input format: - YUV 4:2:0 (IYUV, YV12) -- Image Size: 32 x 32 to 2044 x 2044
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 14 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
-- Output format: - YUV 4:2:2 (YUYV) - RGB16 and RGB32 bpp -- Image Resize - Upscaling ratios ranging from 1:1 to 1:4 in fractional steps - Downscaling ratios ranging from 1:1 to 2:1 in fractional steps and a fixed 4:1 - Ratios provide scaling between QCIF, CIF, QVGA (320 x 240, 240 x 320)
2.3.12
Enhanced Synchronous Dynamic RAM Controller (ESDRAMC)
The Enhanced Synchronous Dynamic RAM Controller (ESDRAMC) provides an interface and control for synchronous DRAM memories for the system. SDRAM memories use a synchronous interface with all signals registered on a clock edge. A command protocol is used for initialization, read, write, and refresh operations to the SDRAM, and is generated on the signals by the controller (when required due to external or internal requests). It has support for both single data rate RAMs and double data rate SDRAMs. It supports 64 Mbits, 128 Mbits, 256 Mbits, and 512 Mbits, 1 Gbit, 2 Gbits, four bank synchronous DRAM by two independent chip selects and with up to 256 Mbytes addressable memory per chip select.
2.3.13
Fast Ethernet Controller (FEC)
The Fast Ethernet Controller (FEC) is designed to support both 10 and 100 Mbps Ethernet/IEEE Std 802.3TM networks. An external transceiver interface and transceiver function are required to complete the interface to the media. The FEC supports the 10/100 Mbps MII and the 10 Mbps-only 7-wire interface, which uses a subset of the MII pins for connection to an external Ethernet transceiver. The FEC incorporates the following features: * Support for three different Ethernet physical interfaces: -- 100-Mbps IEEE 802.3 MII -- 10-Mbps IEEE 802.3 MII -- 10-Mbps 7-wire interface (industry standard) * IEEE 802.3 full duplex flow control * Programmable max frame length supports IEEE Std 802.1TM VLAN tags and priority * Support for full-duplex operation (200 Mbps throughput) with a minimum system clock rate of 50 MHz * Support for half-duplex operation (100 Mbps throughput) with a minimum system clock rate of 25 MHz * Retransmission from transmit FIFO following a collision (no processor bus utilization) * Automatic internal flushing of the receive FIFO for runts (collision fragments) and address recognition rejects (no processor bus utilization) * Address recognition -- Frames with broadcast address may be always accepted or always rejected
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 15
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
* *
*
-- Exact match for single 48-bit individual (unicast) address -- Hash (64-bit hash) check of individual (unicast) addresses -- Hash (64-bit hash) check of group (multicast) addresses -- Promiscuous mode Independent DMA engine with multiple channels allowing transmit data, transmit descriptor, receive data, and receive descriptor accesses to provide high performance Independent RISC-based controller that provides the following functions in the FEC: -- Initialization (those internal registers not initialized by the user or hardware) -- High level control of the DMA channels (initiating DMA transfers) -- Interpreting buffer descriptors -- Address recognition for receive frames -- Random number generation for transmit collision backoff timer The Message Information Block (MIB) in FEC maintains counters for a variety of network events and statistics. The counters supported are the RMON (RFC 1757) Ethernet Statistics group and some of the IEEE 802.3 counters.
2.3.14
General Purpose I/O Module (GPIO)
The general-purpose input/output (GPIO) module provides dedicated general-purpose pins that can be configured as either inputs or outputs. When it is configured as an output, you can write to an internal register to control the state driven on the output pin. When configured as an input, you can detect the state of the input by reading the state of an internal register. The GPIO includes all of the general purpose input/output logic necessary to drive a specific data to the pad and control the direction of the pad using registers in the GPIO module. The ARM926 is able to sample the status of the corresponding pads by reading the appropriate status register. The GPIO supports up to 32 interrupts and has the ability to identify interrupt edges as well as generate three active high interrupts.
2.3.15
General Purpose Timer (GPT)
The i.MX27/MX27L processors contains six identical 32-bit General Purpose Timers (GPT) with programmable prescalers and compare and capture registers. Each timer's counter value can be captured using an external event, and can be configured to trigger a capture event on the rising or/and falling edges of an input pulse. Each GPT can also generate an event on the TOUT pin, and an interrupt when the timer reaches a programmed value. Each GPT has an 11-bit prescaler that provides a programmable clock frequency derived from multiple clock sources, including ipg_clk_32k, ipg_clk_perclk, ipg_clk_perclk/4, and external clock from the TIN pin. The counter has two operation modes: free-run and restart mode. The GPT can work in low-power mode.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 16 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
2.3.16
Inter IC Communication (I2C)
Inter IC Communication (I2C) is a two-wire, bidirectional serial bus that provides a simple, efficient method of data exchange, minimizing the interconnection between devices. This bus is suitable for applications requiring occasional communications over a short distance between many devices. The flexible I2C enables additional devices to be connected to the bus for expansion and system development. The I2C operates up to 400 kbps dependent on pad loading and timing. (For pad requirement details, refer to Phillips I2C Bus Specification, Version 2.1.) The I2C system is a true multiple-master bus, including arbitration and collision detection that prevents data corruption if multiple devices attempt to control the bus simultaneously. This feature supports complex applications with multiprocessor control and can be used for rapid testing and alignment of end products through external connections to an assembly-line computer.
2.3.17
IC Identification Module (IIM)
The IC Identification Module (IIM) provides an interface for reading and in some cases programming and/or overriding identification and control information stored in on-chip fuse elements. The module supports laser fuses (L-Fuses) or electrically-programmable poly fuses (e-Fuses) or both. Contact your Freescale Semiconductor sales office or distributor for additional information on SCC, RTIC, IIM, SAHARA2
2.3.18
JTAG Controller (JTAGC)
The JTAG Controller (JTAGC) module supports debug access to the ARM926 Platform and tristate enable of the I/O pads. The overall strategy is to achieve good test and debug features without increasing the pin count and reducing the complexity of I/O muxing. The JTAG Controller is compatible with IEEE Std 1149.1TM Standard Test Access Port and Boundary Scan Architecture.
2.3.19
Keypad Port (KPP)
The Keypad Port (KPP) is designed to interface with a keypad matrix with 2-contact or 3-point contact keys. KPP is designed to simplify the software task of scanning a keypad matrix. With appropriate software support, the KPP is capable of detecting, debouncing, and decoding one or multiple keys pressed simultaneously in the keypad. The KPP supports up to 8 x 8 external key pad matrix. Its port pins can be used as general purpose I/O. Using an open drain design, the KPP includes glitch suppression circuit design, multiple keys, long key, and standby key detection.
2.3.20
Liquid Crystal Display Controller (LCDC)
The Liquid Crystal Display Controller (LCDC) provides display data for external gray-scale or color LCD panels. The LCDC is capable of supporting black-and-white, gray-scale, passive-matrix color (passive color or CSTN), and active-matrix color (active color or TFT) LCD panels. The LCDC provides the following features: * Configurable AHB bus width (32-bit/64-bit)
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 17
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
* * *
Support for single (non-split) screen monochrome or color LCD panels and self-refresh type LCD panels 16 simultaneous gray-scale levels from a palette of 16 for monochrome display Support for: -- Maximum resolution of 800 x 600 -- Passive color panel: - 4 (mapped to RGB444)/8 (mapped to RGB444)/12 (RGB444) bits per pixel (bpp) -- TFT panel: - 4 (mapped to RGB666)/8 (mapped to RGB666)/12 (RGB444)/16 (RGB565)/18 (RGB666) bpp -- 16 and 256 colors out of a palette of 4096 colors for 4 bpp and 8 bpp CSTN display, respectively -- 16 and 256 colors out of a palette of 256 colors for 4 bpp and 8 bpp TFT display, respectively -- True 4096 colors for a 12 bpp display -- True 64-Kbyte colors for 16 bpp -- True 256-Kbyte colors for 18 bpp -- 16-bit AUO TFT LCD Panel -- 24-bit AUO TFT LCD Panel
2.3.21
Multi-Master Memory Interface (M3IF)/M3IF-ESDCTL/MDDRC Interface
The M3IF-ESDCTL/MDDRC interface is optimized and designed to reduce access latency by generating multiple accesses through the dedicated ESDCTL/MDDRC arbitration (MAB) module, which controls the access to and from the Enhanced SDRAM/MDDR memory controller. For the other port interfaces, the M3IF only arbitrates and forwards the master requests received through the Master Port Gasket (MPG) interface and M3IF Arbitration (M3A) module toward the respective memory controller. The masters that interface with the M3IF include the ARM Platform, FEC, LCDC, H.264, and the USB. The controllers are the ESDCTL/MDDRC, PCMCIA, NFC, and WEIM.
2.3.22
Multi-Layer AHB Crossbar Switch (MAX)
The ARM926EJ-S processor's instruction and data buses--and all alternate bus master interfaces--arbitrate for resources via a 6 x 34 Multi-Layer AHB Crossbar Switch (MAX). There are six (M0-M5) fully functional master ports and three (S0-S2) fully functional slave ports. The MAX is uni-directional. All master and slave ports are AHB-Lite compliant. The design of the crossbar switch enables concurrent transactions to proceed from any master port to any slave port. That is, it is possible for all three slave ports to be active at the same time as a result of three independent master requests. If a particular slave port is simultaneously requested by more than one master port, arbitration logic exists inside the crossbar to allow the higher priority master port to be granted the bus, while stalling the other requestor(s) until that transaction has completed. The slave port arbitration
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 18 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
schemes supported are fixed, programmable fixed, programmable default input port parking, and a round robin arbitration scheme. The Crossbar Switch also monitors the ccm_br input (clock control module bus request), which requests a bus grant from all four slave ports. The priority of ccm_br is programmable and defaults to the highest priority. Upon receiving bus grants for all four output ports, the ccm_bg output will assert. At this point, the clock control and reset module (CRM) can turn off hclk and be assured there are no outstanding AHB transactions in progress. Once the CRM is granted a port, no other master will receive a grant on that port until the CRM bus request (ccm_br) negates.
2.3.23
Memory Stick Host Controller (MSHC)
The Memory Stick Host Controller (MSHC) is located between the AIPI and the Sony Memory Stick and provides support for data transfers between the i.MX27 processor and the Memory Stick (MS). The MSHC consists of two sub-modules; the MSHC gasket and the Sony Memory Stick Host Controller (SMSC). The SMSC module, which is the actual memory stick host controller, is compatible with Sony Memory Stick Ver 1.x and Memory Stick PRO. The gasket connects the AIPI IP bus to the SMSC interface to allow communication and data transfers via the IP Bus. NOTE The i.MX27L does not include the MSHC feature. The MSHC gasket uses a reduced IP Bus interface that supports the IP bus read/write transfers that include a back-to-back read or write. DMA transfers also take place via the IP Bus interface. A transfer can be initiated by the DMA or the host (through the AIPI) response to an MSHC DMA request or interrupt. The SMSC has two DMA address modes--a single address mode and a dual address mode. The MSHC is set to dual-address mode for transfers with the DMA. In dual-address mode, when the MSHC requests a transfer with the DMA request (XDRQ), the DMA will initiate a transfer to the MSHC. NOTE Details regarding the operation of the MSHC module can be found separately in Memory Stick/Memory Stick PRO Host Controller IP Specification 1.3.
2.3.24
NAND Flash Controller (NFC)
NAND Flash Controller (NFC) interfaces standard NAND Flash devices to the i.MX27/MX27L processors and hides the complexities of accessing the NAND Flash. It provides a glueless interface to both 8-bit and 16-bit NAND Flash parts with page sizes of 512 Bytes or 2 Kbytes. Its addressing scheme enables it to access flash devices of almost limitless capacity. The 2-Kbyte RAM buffer of the NAND Flash is used as the boot RAM during a cold reset (if the i.MX27/MX27L device is configured for a boot to be carried out from the NAND Flash device). After the boot procedure completes, the RAM is available as buffer RAM. In addition, the NAND Flash controller provides an X16-bit and X32-bit interface to the AHB bus on the chip side, and an X8/X16 interface to the NAND Flash device on the external side.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 19
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
2.3.25
Personal Computer Memory Card International Association (PCMCIA)
The Personal Computer Memory Card International Association (PCMCIA) provides the PCMCIA 2.1 standard, which defines the usage of memory and I/O devices as insertable and exchangeable peripherals for personal computers or PDAs. Examples of these types of devices include CompactFlash and WLAN adapters. The pcmcia_if host adapter module provides the control logic for PCMCIA socket interfaces, and requires some additional external analog power switching logic and buffering. The additional external buffers allow the pcmcia_if host adapter module to support one PCMCIA socket. The pcmcia_if shares its chip level I/O with the external interface to memory (EIM) pins. Additional logic is required to multiplex the EIM and the pcmcia_if on the same pins.
2.3.26
Digital Phase Lock Loop (DPLL)
Two on-chip Digital Phase Lock Loop (DPLLs) provide clock generation in digital and mixed analog/digital chips designed for wireless communication and other applications. The DPLLs produce a high-frequency chip clock signals with a low frequency and phase jitter.
2.3.27
Pulse-Width Modulator (PWM)
The Pulse-Width Modulator (PWM) has a 16-bit counter and is optimized to generate sounds from stored sample audio images; it can also generate tones. The PWM uses 16-bit resolution and a 4 x 16 data FIFO to generate sound. The 16-bit up-counter has a source selectable clock with 4 x 16 FIFO to minimize interrupt overhead. Clock-in frequency is controlled by a 12-bit prescaler for the division of a clock. Capable of sound and melody generation, the PWM has an active-high or active-low configurable output, and can be programmed to be active in low-power and debug modes. The PWM can be programmed to generate interrupts at compare and rollover events.
2.3.28
Real Time Clock (RTC)
The Real Time Clock (RTC) module maintains the system clock, provides stopwatch, alarm, and interrupt functions, and supports the following features: * Full clock--days, hours, minutes, seconds * Minute countdown timer with interrupt * Programmable daily alarm with interrupt * Sampling timer with interrupt * Once-per-day, once-per-hour, once-per-minute, and once-per-second interrupts * Operation at 32.768 kHz or 32 kHz, or 38.4 kHz (determined by reference clock crystal) The prescaler converts the incoming crystal reference clock to a 1 Hz signal, which is used to increment the seconds, minutes, hours, and days TOD counters. The alarm functions, when enabled, generate RTC interrupts when the TOD settings reach programmed values. The sampling timer generates fixed-frequency interrupts, and the minute stopwatch allows for efficient interrupts on very small boundaries.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 20 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
2.3.29
Run-TIme Integrity Checker (RTIC)
The Run-Time Integrity Checker (RTIC) is one of the security components in the i.MX27/MX27L processors. Its purpose is to ensure the integrity of the peripheral memory contents and assist with boot authentication. The RTIC has the ability to verify the memory contents during system boot and during run-time execution. If the memory contents at runtime fail to match the hash signature, an error in the security monitor is triggered. Contact your Freescale Semiconductor sales office or distributor for additional information on SCC, RTIC, IIM, SAHARA2
2.3.30
Symmetric/Asymmetric Hashing and Random Accelerator (SAHARA2)
SAHARA2 is a security co-processor, it implements encryption algorithms (AES, DES, and 3DES), hashing algorithms (MD5, SHA-1, SHA_224, and SHA-256), stream cipher algorithm (ARC4), and a hardware random number generator. Contact your Freescale Semiconductor sales office or distributor for additional information on SCC, RTIC, IIM, SAHARA2
2.3.31
Security Controller Module (SCC)
The Security Controller Module (SCC) is a hardware security component. Overall, its primary functionality is associated with establishing a centralized security state controller and hardware security state with a hardware configured, unalterable security policy. Contact your Freescale Semiconductor sales office or distributor for additional information on SCC, RTIC, IIM, and SAHARA2.
2.3.32
Secure Digital Host Controller (SDHC)
The Secure Digital Host Controller (SDHC) controls the MultiMedia Card (MMC), Secure Digital (SD) memory, and I/O cards by sending commands to cards and performing data accesses to/from the cards. The Multimedia Card/Secure Digital Host (MMC/SD) module integrates both MMC support along with SD memory and I/O functions. The SDHC is fully compatible with the MMC System Specification Version 3.0, as well as with the SD Memory Card Specification 1.0, and SD I/O Specification 1.0 with 1/4 channel(s). The maximum data rate in 4-bit mode is 100 Mbps. The SDHC uses a built-in programmable frequency counter for the SDHC bus, and provides a maskable hardware interrupt for an SDIO interrupt, internal status, and FIFO status. It has a pair of 32 x 16-bit data FIFO buffers built in. The MultiMedia Card (MMC) is a universal, low-cost data storage and communication media that is designed to cover a wide area of applications, including, for example, electronic toys, organizers, PDAs, and smart phones. The MMC communication is based on an advanced 7-pin serial bus designed to operate in a low-voltage range. The Secure Digital Card (SD) is an evolution of MMC technology, with two additional pins in the form factor. It is specifically designed to meet the security, capacity, performance, and environment requirements inherent in newly emerging audio and video consumer electronic devices. The physical form
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 21
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
factor, pin assignment, and data transfer protocol are forward-compatible with the MultiMedia Card with some additions. Under SD, it can be categorized into Memory and I/O. The memory card invokes a copyright protection mechanism that complies with the security of the SDMI standard, which is faster and provides the capability for a higher memory capacity. The I/O card provides high-speed data I/O with low-power consumption for mobile electronic devices.
2.3.33
Smart Liquid Crystal Display Controller Module (SLCDC)
The Smart Liquid Crystal Display Controller (SLCDC) module transfers data from the display memory buffer to the external display device. Direct Memory Access (DMA) transfers the data transparently with minimal software intervention. Bus utilization of the DMA is controllable and deterministic. As cellular phone displays become larger and more colorful, demands on the processor increase. More CPU power is needed to render and manage the image. The role of the display controller is to reduce the CPU's involvement in the transfer of data from memory to the display device so the CPU can concentrate on image rendering. DMA is used to optimize the transfer. Embedded control information needed by the display device is automatically read from a second buffer in system memory and inserted into the data stream at the proper time to completely eliminate the CPU's role in the transfer. A typical scenario for a cellular phone display is to have the display image rendered in main system memory. After the image is complete, the CPU triggers the SLCDC module to transfer the image to the display device. Image transfer is accomplished by burst DMA, which steals bus cycles from the CPU. Cycle-stealing behavior is programmable so bus use is kept within predefined bounds. After the transfer is complete, a maskable interrupt is generated indicating the status. For animated displays, it is suggested that a two-buffer ping-pong scheme be implemented so that the DMA is fetching data from one buffer while the next image is rendered into the other. Several display sizes and types are used in the various products that use the SLCDC. The SLCDC module has the capability of directly interfacing to the selected display devices. Both serial and parallel interfaces are supported. The SLCDC module only supports writes to the display controller. SLCDC read operations from the display controller are not supported.
2.3.34
Synchronous Serial Interface (SSI)
The Synchronous Serial Interface (SSI) is a full-duplex serial port that allows the chip to communicate with a variety of serial devices. These serial devices can be standard codecs, Digital Signal Processors (DSPs), microprocessors, peripherals, and popular industry audio codecs that implement the inter-IC sound bus standard (I2S) and Intel AC97 standard. The SSI is typically used to transfer samples in a periodic manner. The SSI consists of independent transmitter and receiver sections with independent clock generation and frame synchronization. The SSI contains independent (asynchronous) or shared (synchronous) transmit and receive sections with separate or shared internal/external clocks and frame syncs, operating in Master or Slave mode. The SSI can work in Normal mode operation using frame sync, and in Network mode operation allowing multiple devices to share the port with as many as thirty-two time slots. The SSI provides two sets of Transmit and Receive FIFOs. Each of the four FIFOs is 8 x 24 bits. The two sets of Tx/RX FIFOs can be used in Network mode to provide two independent channels for transmission
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 22 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
and reception. It also has programmable data interface modes such as I2S, LSB, and MSB aligned and programmable word lengths. Other program options include frame sync, clock generation, and programmable I2S modes (Master, Slave, or Normal). Oversampling clock, ccm_ssi_clk is available as output from SRCK in I2S Master mode. In addition to AC97 support, the SSI has completely separate clock and frame sync selections for the receive and transmit sections. In the AC97 standard, the clock is taken from an external source and frame sync is generated internally. The SSI also has a programmable internal clock divider and Time Slot Mask registers for reduced CPU overhead (for Tx and RX both).
2.3.35
Universal Asynchronous Receiver/Transmitter (UART)
The i.MX27/MX27L processors contain six UART modules. Each UART module is capable of standard RS-232 non-return-to-zero (NRZ) encoding format and IrDA-compatible infrared modes. The UART provides serial communication capability with external devices through an RS-232 cable or through use of external circuitry that converts infrared signals to electrical signals (for reception); or it transforms electrical signals to signals that drive an infrared LED (for transmission) to provide low-speed IrDA compatibility. The UART transmits and receives characters that are either 7 or 8 bits in length (program selectable). To transmit, data is written from the peripheral data bus to a 32-byte transmitter FIFO (TxFIFO). This data is passed to the shift register and shifted serially out on the transmitter pin (TXD). To receive, data is received serially from the receiver pin (RXD) and stored in a 32-half-word-deep receiver FIFO (RxFIFO). The received data is retrieved from the RxFIFO on the peripheral data bus. The RxFIFO and TxFIFO generate maskable interrupts as well as DMA requests when the data level in each of the FIFO reaches a programmed threshold level. The UART generates baud rates based on a programmable divisor and input clock. The UART also contains programmable auto baud detection circuitry to receive 1 or 2 stop bits as well as odd, even, or no parity. The receiver detects framing errors, idle conditions, BREAK characters, parity errors, and overrun errors.
2.3.36
Universal Serial Bus (USB)
The i.MX27/MX27L processors provide three USB ports. The USB module provides high performance USB On-The-Go (OTG) functionality, compliant with the USB 2.0 specification, the OTG supplement, and the ULPI 1.0 Low Pin Count specification. The module consists of three independent USB cores, each controlling one USB port. In addition to the USB cores, the USB module provides for Transceiverless Link (TLL) operation on host Ports 1 and 2, and provides the ability of routing the OTG transceiver interface to Host Port 1 such that this transceiver can be used to communicate with a USB peripheral connected to Host Port 1. The USB module has two connections to the CPU bus--one IP-bus connection for register accesses and one AHB-bus connection for the DMA transfer of data to and from the FIFOs. The USB module includes the following features: * Full Speed/Low speed Host only core (HOST 1) * Transceiverless Link Logic (TLL) for on board connection to a FS/LS USB peripheral
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 23
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
* * * * *
Bypass mode to route Host Port 1 signals to OTG I/O port High Speed /Full Speed/Low Speed Host Only core (Host 2) Full Speed/Low Speed interface for Serial transceiver TLL function for direct connection to USB peripheral in FS/LS (serial) operation High-speed OTG core
The USB module has two main modes of operation: Normal mode and Bypass mode. Furthermore, the USB interfaces can be configured for high-speed operation (480 Mbps) and/or full/low speed operation (12/1.5 Mbps). In Normal mode, each USB core controls its corresponding port. In additional to th4e major operational modes, each port can work in one or more modes, as follows: PHY mode In PHY mode, an external serial transceiver is connected to the port. This is used for off-board USB connections. TLL mode In TLL mode, internal logic is enabled to emulate the functionality of two back-to-back connected transceivers. This mode is typically used for on-board USB connections to USB-capable peripherals. Host Port 2 supports ULPI and Serial Transceivers. The OTG port requires a transceiver and is intended for off-board USB connections. Serial Interface mode In serial mode, a serial OTG transceiver must be connected. The port does not support dedicated signals for OTG signaling. Instead, a transceiver with built-in OTG registers must be used. Typically, the Transceiver registers are accessible over an I2C or SPI interface. ULPI mode In this mode, a ULPI transceiver is connected to the port pins to support high-speed off board USB connection. Bypass mode Bypass mode affects the operation of the OTG port and Host Port 1. This mode is only available when a serial transceiver is used on the OTG port, and the peripheral device on Port 1 is using a TLL connection. Bypass mode is activated by setting the bypass bit in the USBCONTROL register. In this mode, the USB OTG port connections are internally routed to the USB Host 1 port, such that the transceiver on the OTG port connects to a peripheral USB device on Host Port 1. The OTG core and the Host 1 core are disconnected from their ports when bypass is active. Low Power mode Each of the three USB cores has an associated power control module that is controlled by the USB core and clocked on a 32-kHz clock. When a USB bus is idle, the transceiver can be placed in low-power mode (suspend), after which the clocks to the USB core can be stopped. The 32-kHz low power clock must remain active as it is needed for walk-up detection.
2.3.37
Watchdog Timer Module (WDOG)
The Watchdog Timer module (WDOG) protects against system failures by providing a method of escaping from unexpected events or programming errors. Once the WDOG module is activated, it must be serviced by software on a periodic basis. If servicing does not take place, the timer times out. Upon a time-out, the WDOG Timer module either asserts the wdog signal or a system reset signal wdog_rst, depending on
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 24 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
software configuration. The WDOG Timer module also generates a system reset via a software write to the Watchdog Control Register (WCR) when there is a detection of a clock monitor event, an external reset, an external JTAG reset signal, or if a power-on-reset has occurred.
2.3.38
Wireless External Interface Module (WEIM)
The Wireless External Interface Module (WEIM) handles the interface to devices external to the chip, including generation of chip selects, clocks and controls for external peripherals and memory. It provides asynchronous and synchronous access to devices with an SRAM-like interface. The WEIM includes six chip selects for external devices, with two CS signals covering a range of 128 Mbytes, and the other four each covering a range of 32 Mbytes. The 128-Mbyte range can be increased to 256 Mbytes when combined with the two signals. The WEIM offers selectable protection for each chip select as well as programmable data port size. There is a programmable wait-state generator for each chip select and support for Big Endian and Little Endian modes of operation per access.
2.3.39
Video Codec
The Video Codec module is the video processing module in the i.MX27 processor. It supports full duplex video codec with 25 fps VGA resolution, supports multi-party calls, and integrates multiple video processing standards, including H.264 BP, MPEG-4 SP, and H.263 P3 (including annex I, J, K, and T), D1 resolution, 30 fps--half-duplex. NOTE The Video Codec feature is not available on the i.MX27L It has three 64-bit AHB-Lite master bus interfaces connecting to the EMI, which includes two read channels and one write channel. Its 32-bit AHB-Lite master bus is connected to ARM Platform to access system-internal SRAM. The Video Codec module contains three major architectural components: video codec processing IP, AXI-to-AHB bus protocol transfer module, and a 32-bit to 64-bit AHB master bus protocol transfer module. The Video Codec module supports following video stream processing features: * Multi-standard video codec -- MPEG-4 part-II simple profile encoding/decoding -- H.264/AVC baseline profile encoding/decoding -- H.263 P3 encoding/decoding -- Multi-party call: max processing four image/bitstream encoding and/or decoding simultaneously -- Multi-format: for example, encodes MPEG-4 bitstream, and decodes H.264 bitstream simultaneously * Coding tools -- High-performance motion estimation - Single reference frame for both MPEG-4 and H.264 encoding
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 25
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Functional Description and Application Information
*
*
- Support 16 reference frame for H.264 decoding - Quarter-pel and half-pel accuracy motion estimation - [+/-16, +/-16] Search range - Unrestricted motion vector -- All variable block sizes are supported (in case of encoding, 8 x 4, 4 x 8, and 4 x 4 block sizes are not supported). -- MPEG-4 AC/DC prediction and H.264 Intra prediction -- H.263 Annex I, J, K(RS = 0 and ASO =0), and T are supported. In case of encoding, the Annex I and K(RS=1 or ASO=1) are not supported. -- CIR (Cyclic Intra Refresh)/AIR (Adaptive Intra Refresh) -- Error resilience tools - MPEG-4 re-synchronize marker and data-partitioning with RVLC (fixed number of bits/macroblocks between macroblocks) - H.264/AVC FMO and ASO - H.263 slice structured mode -- Bit-rate control (CBR and VBR) Pre/post rotation/mirroring -- 8 rotation/mirroring modes for image to be encoded -- 8 rotation/mirroring modes for image to be displayed Programmability -- Embeds 16-bit DSP processor that is dedicated to processing bitstream and driving codec hardware -- General purpose registers and interrupt generation for communication between system and video codec module
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 26 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Signal Descriptions
3
Signal Descriptions
This section discusses the following: * Identifies and defines all device signals in text, tables, and (as appropriate) figures. Signals can be organized by group, as applicable. * Contains pin-assignment/contact-connection diagrams, if the sequence of information in the data sheet requires them to be included here. Table 3 shows the i.MX27/MX27L signal descriptions.
Table 3. i.MX27/MX27L Signal Descriptions
Pad Name Function/Notes External Bus/Chip Select (EMI) A [13:0] MA10 A [25:14] SDBA[1:0] SD[31:0] SDQS[3:0] DQM0-DQM3 EB0 EB1 OE CS [5:0] Address bus signals, shared with SDRAM/MDDR, WEIM and PCMCIA, A[10] for SDRAM/MDDR is not the address but the pre-charge bank select signal. Address bus signals for SDRAM/MDDR Address bus signals, shared with WEIM and PCMCIA SDRAM/MDDR bank address signals Data bus signals for SDRAM, MDDR MDDR data sample strobe signals SDRAM data mask strobe signals Active low external enable byte signal that controls D [15:8], shared with PCMCIA PC_REG. Active low external enable byte signal that controls D [7:0], shared with PCMCIA PC_IORD. Memory Output Enable--Active low output enables external data bus, shared with PCMCIA PC_IOWR. Chip Select--The chip select signals CS [3:2] are multiplexed with CSD [1:0] and are selected by the Function Multiplexing Control Register (FMCR) in the System Control chapter. By default CSD [1:0] is selected. DTACK is multiplexed with CS4. CS[5:4] are multiplexed with ETMTRACECLK and ETMTRACESYNC; PF22, 21. Active low input signal sent by flash device to the EIM whenever the flash device must terminate an on-going burst sequence and initiate a new (long first access) burst sequence. Active low signal sent by flash device causing external burst device to latch the starting burst address. Clock signal sent to external synchronous memories (such as burst flash) during burst mode. RW signal--Indicates whether external access is a read (high) or write (low) cycle. This signal is also shared with the PCMCIA PC_WE. SDRAM/MDDR Row Address Select signal SDRAM/MDDR Column Address Select signal SDRAM Write Enable signal SDRAM Clock Enable 0
ECB LBA BCLK RW RAS CAS SDWE SDCKE0
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 27
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Signal Descriptions
Table 3. i.MX27/MX27L Signal Descriptions (continued)
Pad Name SDCKE1 SDCLK SDCLK_B NFWE_B NFRE_B NFALE NFCLE NFWP_B NFCE_B NFRB D[15:0] PC_CD1_B PC_CD2_B PC_WAIT_B PC_READY PC_PWRON PC_VS1 PC_VS2 PC_BVD1 PC_BVD2 PC_RST IOIS16 PC_RW_B PC_POE SDRAM Clock Enable 1 SDRAM Clock SDRAM Clock_B NFC Write enable signal, multiplexed with ETMPIPESTAT2; PF6 NFC Read enable signal, multiplexed with ETMPIPESTAT1; PF5 NFC Address latch signal, multiplexed with ETMPIPESTAT0; PF4 NFC Command latch signal, multiplexed with ETMTRACEPKT0; PF1 NFC Write Permit signal, multiplexed with ETMTRACEPKT1; PF2 NFC Chip enable signal, multiplexed with ETMTRACEPKT2; PF3 NFC read Busy signal, multiplexed with ETMTRACEPKT3; PF0 Data Bus signal, shared with EMI, PCMCIA, and NFC PCMCIA card detect signal, multiplexed with ATA ATA_DIOR signal; PF20 PCMCIA card detect signal, multiplexed with ATA ATA_DIOW signal; PF19 PCMCIA WAIT signal, multiplexed with ATA ATA_CS1 signal; PF18 PCMCIA READY/IRQ signal, multiplexed with ATA ATA_CS0 signal; PF17 PCMCIA signal, multiplexed with ATA ATA_DA2 signal; PF16 PCMCIA voltage sense signal, multiplexed with ATA ATA_DA1 signal; PF14 PCMCIA voltage sense signal, multiplexed with ATA ATA_DA0 signal; PF13 PCMCIA Battery voltage detect signal, multiplexed with ATA ATA_DMARQ signal; PF12 PCMCIA Battery voltage detect signal, multiplexed with ATA ATA_DMACK signalPF11 PCMCIA card reset signal, multiplexed with ATA ATA_RESET_B signal; PF10 PCMCIA mode signal, multiplexed with ATA ATA_INTRQ signal; PF9 PCMCIA read write signal, multiplexed with ATA ATA_IORDY signal; PF8 PCMCIA output enable signal, multiplexed with ATA ATA_BUFFER_EN signal; PF7 Clocks and Resets CLKO EXT_60M EXT_266M OSC26M_TEST RESET_IN Clock Out signal selected from internal clock signals. Refer to the clock controller for internal clock selection; PF15. This is a special factory test signal. To ensure proper operation, connect this signal to ground. This is a special factory test signal. To ensure proper operation, connect this signal to ground. This is a special factory test signal. To ensure proper operation, leave this signal as a no connect. Master Reset--External active low Schmitt trigger input signal. When this signal goes active, all modules (except the reset module, SDRAMC module, and the clock control module) are reset. Function/Notes
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 28 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Signal Descriptions
Table 3. i.MX27/MX27L Signal Descriptions (continued)
Pad Name RESET_OUT POR XTAL26M EXTAL26M CLKMODE[1:0] EXTAL32K XTAL32K Power_cut Power_on_reset osc32K_bypass Function/Notes Reset_Out--Output from the internal Hreset_b; and the Hreset can be caused by all reset source: power on reset, system reset (RESET_IN), and watchdog reset. Power On Reset--Active low Schmitt trigger input signal. The POR signal is normally generated by an external RC circuit designed to detect a power-up event. Oscillator output to external crystal Crystal input (26 MHz), or a 16 MHz to 32 MHz oscillator (or square-wave) input when internal oscillator circuit is shut down. These are special factory test signals. To ensure proper operation, do not connect to these signals. 32 kHz crystal input (Note: in the RTC power domain) Oscillator output to 32 kHz crystal (Note: in the RTC power domain) (Note: in the RTC power domain) (Note: in the RTC power domain) The signal for osc32k input bypass (Note: in the RTC power domain) Bootstrap BOOT [3:0] System Boot Mode Select--The operational system boot mode of the i.MX27/MX27L processor upon system reset is determined by the settings of these pins. BOOT[1:0] are also used as handshake signals to PMIC(VSTBY). JTAG JTAG_CTRL JTAG Controller select signal--JTAG_CTRL is sampled during rising edge of TRST. Must be pulled to logic high for proper JTAG interface to debugger. Pulling JTAG_CRTL low is for internal test purposes only. Test Reset Pin--External active low signal used to asynchronously initialize the JTAG controller. Serial Output for test instructions and data. Changes on the falling edge of TCK. Serial Input for test instructions and data. Sampled on the rising edge of TCK. Test Clock to synchronize test logic and control register access through the JTAG port. Test Mode Select to sequence JTAG test controller's state machine. Sampled on rising edge of TCK. JTAG Return Clock used to enhance stability of JTAG debug interface devices. This signal is multiplexed with 1-Wire; thus, utilizing 1-Wire will render RTCK unusable and vice versa; PE16. Secure Digital Interface (X2) SD1_CMD SD Command bidirectional signal--If the system designer does not want to make use of the internal pull-up, via the Pull-up enable register, a 4. 7K-69 K external pull up resistor must be added. This signal is multiplexed with CSPI3_MOSI; PE22. SD Output Clock. This signal is multiplexed with CSPI3_SCLK; PE23.
TRST TDO TDI TCK TMS RTCK
SD1_CLK
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 29
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Signal Descriptions
Table 3. i.MX27/MX27L Signal Descriptions (continued)
Pad Name SD1_D[3:0] Function/Notes SD Data bidirectional signals--If the system designer does not want to make use of the internal pull-up, via the Pull-up enable register, a 50 K-69 K external pull up resistor must be added. SD1_D[3] is muxed with CSPI3_SS while SD1_D[0] is muxed with CSPI3_MISO PE21-18. SD Command bidirectional signal. This signal is multiplexed with MSHC_BS; through GPIO multiplexed with SLCDC1_CS; PB8. SD Output Clock signal. This signal is multiplexed with MSHC_SCLK, through GPIO multiplexed with SLCDC1_CLK; PB9. SD Data bidirectional signals. SD2_D[3:0] multiplexed with MSHC_DATA[0:3], also through GPIO SD2_1:0] multiplexed with SLCDC1_RS and SLDCD1_D0; PB7-PB4. SD Command bidirectional signal. This signal is multiplexed with ETMTRACEPKT15 and also through GPIO PD1 multiplexed with FEC_TXD0. SD Output Clock signal. This signal is through GPIO PD0 multiplexed with FEC_TXD1.
SD2_CMD SD2_CLK SD2_D[3:0] SD3_CMD SD3_CLK
Note: SD3_DATA is multiplexed with ATA_DATA3-0. UARTs (X6) UART1_RTS UART1_CTS UART1_RXD UART1_TXD UART2_RXD UART2_TXD UART2_RTS UART2_CTS UART3_RTS UART3_CTS UART3_RXD UART3_TXD Request to Send input signal; PE15 Clear to Send output signal; PE14 Receive Data input signal; PE13 Transmit Data output signal, PE12 Receive Data input signal. This signal is multiplexed with KP_ROW6 signal from KPP; PE7. Transmit Data output signal. This signal is multiplexed with KP_COL6 signal from KPP; PE6. Request to Send input signal. This signal is multiplexed with KP_ROW7 signal from KPP; PE4. Clear to Send output signal. This signal is multiplexed with KP_COL7 signal from KPP; PE3. Request to Send input signal, PE11 Clear to Send output signal; PE10 Receive Data input signal; PE9 Transmit Data output signal; PE8
Note: UART 4, 5, and 6 are multiplexed with COMS Sensor Interface signals. Keypad KP_COL[5:0] Keypad Column selection signals. KP_COL[7:6] are multiplexed with UART2_CTS and UART2_TXD respectively. Alternatively, KP_COL6 is also available on the internal factory test signal TEST_WB2. The Function Multiplexing Control Register in the System Control chapter must be used in conjunction with programming the GPIO multiplexing (to select the alternate signal multiplexing) to choose which signal KP_COL6 is available. Keypad Row selection signals. KP_ROW[7:6] are multiplexed with UART2_RTS and UART2_RXD signals respectively. The Function Multiplexing Control Register in the System Control chapter must be used in conjunction with programming the GPIO multiplexing (to select the alternate signal multiplexing) to choose which signals KP_ROW6 and KP_ROW7 are available.
KP_ROW[5:0]
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 30 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Signal Descriptions
Table 3. i.MX27/MX27L Signal Descriptions (continued)
Pad Name Function/Notes
Note: KP_COL[7:6] and KP_ROW[7:6] are multiplexed with UART2 signals as show above, also see UARTs table. PWM PWMO PWM Output. This signal is multiplexed with PC_SPKOUT of PCMCIA, as well as TOUT2 and TOUT3 of the General Purpose Timer module; PE5. CSPI (X3) CSPI1_MOSI CSPI1_MISO CSPI1_SS[2:0] CSPI1_SCLK CSPI1_RDY CSPI2_MOSI CSPI2_MISO CSPI2_SS[2:0] CSPI2_SCLK Master Out/Slave In signal, PD31 Master In/Slave Out signal, PD30 Slave Select (Selectable polarity) signal, the CSPI1_SS2 is multiplexed with USBH2_DATA5/RCV; and CSPI1_SS1 is multiplexed with EXT_DMAGRANT; PD26-28. Serial Clock signal, PD29 Serial Data Ready signal, shared with Ext_DMAReq_B signal; PD25 Master Out/Slave In signal, multiplexed with USBH2_DATA1/TXDP; PD24 Master In/Slave Out signal, multiplexed with USBH2_DATA2/TXDm; PD23 Slave Select (Selectable polarity) signals, multiplexed with USBH2_DATA4/RXDM, USBH2_DATA3/RXDP, USBH2_DATA6/SPEED; PD19-PD21 Serial Clock signal, multiplexed with USBH2_DATA0/OEn; PD22
Note: CSPI3 CSPI3_MOSI, CSPI3_MISO, CSPI3_SS, andCSPI3_SCLK are multiplexed with SD1 signals. I2C I2C2_SCL I2C2_SDA I2C_CLK I2C_DATA I2C2 Clock, through GPIO, multiplexed with SLCDC_data8; PC6 I2C2 Data, through GPIO, multiplexed with SLCDC_data7; PC5 I2C1 Clock; PD18 I2C1 Data; PD17 CMOS Sensor Interface CSI_HSYNC CSI_VSYNC CSI_D7 CSI_D6 CSI_D5 CSI_PIXCLK CSI_MCLK CSI_D4 CSI_D3 CSI_D2 Sensor port horizontal sync, multiplexed with UART5_RTSP; PB21 Sensor port vertical sync, multiplexed with UART5_CTS; PB20 Sensor port data, multiplexed with UART5_RXD; PB19 Sensor port data, multiplexed with UART5_TXD; PB18 Sensor port data; PB17 Sensor port data latch clock; PB16 Sensor port master clock, PB15 Sensor port data, PD14 Sensor port data, multiplexed with UART6_RTS; PB13 Sensor port data, multiplexed with UART6_CTS; PB12
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 31
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Signal Descriptions
Table 3. i.MX27/MX27L Signal Descriptions (continued)
Pad Name CSI_D1 CSI_D0 Function/Notes Sensor port data, multiplexed with UART6_RXD; PB11 Sensor port data, multiplexed with UART6_TXD; PB10 Serial Audio Port--SSI (Configurable to I2S Protocol and AC97) (2 to 4) SSI1_CLK SSI1_TXD SSI1_RXD SSI1_FS SSI2_CLK SSI2_TXD SSI2_RXD SSI2_FS SSI3_CLK SSI3_TXD SSI3_RXD SSI3_FS SSI4_CLK SSI4_TXD SSI4_RXD SSI4_FS Serial clock signal that is output in master or input in slave; PC23 Transmit serial data; PC22 Receive serial data; PC21 Frame Sync signal that is output in master and input in slave; PC20 Serial clock signal that is output in master or input in slave, multiplexed with GPT4_TIN. PC27 Transmit serial data signal, multiplexed with GPT4_TOUT; PC26 Receive serial data, multiplexed with GPT5_TIN; PC25 Frame Sync signal which is output in master and input in slave, multiplexed with GPT5_TOUT: PC24 Serial clock signal which is output in master or input in slave. This signal is multiplexed with SLCDC2_CLK; through GPIO multiplexed with PC_WAIT_B; PC31. Transmit serial data signal which is multiplexed with SLCDC2_CS, through GPIO multiplexed with PC_READY; PC30 Receive serial data which is multiplexed with SLCDC2_RS; through GPIO multiplexed with PC_VS1; PC29 Frame Sync signal which is output in master and input in slave. This signal is multiplexed with SLCDC2_D0; through GPIO multiplexed with PC_VS1; PC28. Serial clock signal which is output in master or input in slave; through GPIO multiplexed with PC_BVD1; PC19 Transmit serial data; through GPIO multiplexed with PC_BVD2; PC18 Receive serial data; through GPIO multiplexed with IOIS16; PC17 Frame Sync signal which is output in master and input in slave; PC16 General Purpose Timers (X6) TIN Timer Input Capture or Timer Input Clock--The signal on this input is applied to GPT 1-3 simultaneously. This signal is muxed with the Walk-up Guard Mode WKGD signal in the PLL, Clock, and Reset Controller module, and is also multiplexed with GPT6_TOUT; PC15. Timer Output signal from General Purpose Timer1 (GPT1). This signal is multiplexed with SSI1_MCLK and SSI2_MCLK signal of SSI1 and SSI2. The pin name of this signal is simply TOUT, and is also multiplexed with GPT6_TIN; PC14.
TOUT1
Note: TOUT2, TOUT3 are multiplexed with PWMO pad; GPT4 and GPT5 signals are multiplexed with SSI2 pads. USB2.0 USBOTG_DIR/TXDM USBOTG_STP/TXDM USB OTG direction/Transmit Data Minus signal, multiplexed with KP_ROW7A; PE2 USB OTG Stop signal/Transmit Data Minus signal, multiplexed with KP_ROW6A; PE1
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 32 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Signal Descriptions
Table 3. i.MX27/MX27L Signal Descriptions (continued)
Pad Name USBOTG_NXT/TXDM USBOTG_CLK/TXDM USBOTG_DATA7/SUSPEND USBH2_STP/TXDM USBH2_NXT/TXDM USBH2_DATA7/SUSPEND USBH2_DIR/TXDM USBH2_CLK/TXDM USBOTG_DATA3/RXDP USBOTG_DATA4/RXDM USBOTG_DATA1/TXDP USBOTG_DATA2/TXDm USBOTG_DATA0/Oen USBOTG_DATA6/SPEED USBOTG_DATA5/RCV USBH1_RXDP USBH1_RXDM USBH1_TXDP USBH1_TXDM USBH1_OE_B USBH1_FS USBH1_RCV USB_OC_B USB_PWR USBH1_SUSP Function/Notes USB OTG NEXT/Transmit Data Minus signal, multiplexed with KP_COL6A; PE0 USB OTG Clock/Transmit Data Minus signal, PE24 USB OTG Data7/Suspend signal, PE25 USB Host2 Stop signal/Transmit Data Minus signal, PA4 USB Host2 NEXT/Transmit Data Minus signal, PA3 USB Host2 Data7/Suspend signal, PA2 USB Host2 Direction/Transmit Data Minus signal, PA1 USB Host2 Clock/Transmit Data Minus signal; PA0 USB OTG data4/Receive Data Plus signal; multiplexed with SLCDC1_DAT15 through PC13 USB OTG data4/Receive Data Minus signal; multiplexed with SLCDC1_DAT14 through PC12 USB OTG data1/Transmit Data Plus signal; multiplexed with SLCDC1_DAT13 through PC11 USB OTG data2/Transmit Data Minus signal; multiplexed with SLCDC1_DAT12 through PC10 USB OTG data0/Output Enable signal; multiplexed with SLCDC1_DAT11 through PC9 USB OTG data6/Suspend signal; multiplexed with SLCDC1_DAT10 and USBG_TXR_INT_B through PC8 USB OTG data5/RCV signal; multiplexed with SLCDC1_DAT9 through PC7 USB Host1 Receive Data Plus signal, multiplexed with UART4_RXD; multiplexed with SLCDC1_DAT6 and UART4_RTS_ALT through PB31 USB Host1 Receive Data Minus signal; multiplexed with SLCDC1_DAT5 and UART4_CTS through PB30 USB Host1 Transmit Data Plus signal; multiplexed with UART4_CTS, multiplexed with SLCDC1_DAT4 and UART4_RXD_ALT through PB29 USB Host1 Transmit Data Minus signal; multiplexed with UART4_TXD, multiplexed with SLCDC1_DAT3 through PB28 USB Host1 Output Enable signal; multiplexed with SLCDC1_DAT2 through PB27 USB Host1 Full Speed output signal, multiplexed with UART4_RTS, multiplexed with SLCDC1_DAT1 through PB26 USB Host1 RCV signal; multiplexed with SLCDC1_DAT0 through PB25 USB OC signal. PB24 USB Power signal; PB23 USB Host1 Suspend signal; PB22 LCD Controller and Smart LCD Controller OE_ACD CONTRAST Alternate Crystal Direction/Output Enable; PA31 This signal is used to control the LCD bias voltage as contrast control; PA30
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 33
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Signal Descriptions
Table 3. i.MX27/MX27L Signal Descriptions (continued)
Pad Name VSYNC Function/Notes Frame Sync or Vsync--This signal also serves as the clock signal output for gate; driver (dedicated signal SPS for Sharp panel HR-TFT); PA29. Line Pulse or HSync; PA28 Sampling start signal for left and right scanning. Through GPIO, this signal is multiplexed with the SLCDC1_CLK; PA27. Control signal output for source driver (Sharp panel dedicated signal). This signal is multiplexed with the SLCDC1_CS; PA26. Start signal output for gate driver. This signal is invert version of PS (Sharp panel dedicated signal). This signal is multiplexed with the SLCDC1_RS; PA25. Signal for common electrode driving signal preparation (Sharp panel dedicated signal). This signal is multiplexed with SLCDC1_D0; PA24. LCD Data Bus--All LCD signals are driven low after reset and when LCD is off. Through GPIO, LD[15:0] signals are multiplexed with SLCDC1_DAT[15:0], SLCDC. PA23-PA6. Shift Clock; PA5
HSYNC SPL_SPR PS CLS REV LD [17:0] LSCLK
Note: SLCDC signals are multiplexed with LCDC signals. ATA (not available on i.MX27L) ATA_DATA15-0 ATA Data Bus, [15:0] are multiplexed with ETMTRACEPKT4-12, FEC_MDIO, ETMTRACEPKT13-14 SD3_D3-0; Through GPIO also are multiplexed with SLCDC 15-0, and FEC signals; PF23, PD16-PD2. Noisy I/O Supply Pins NVDD1-15, AVDD Noisy Supply for the I/O pins. There are 16 I/O voltage pads, NVDD1 through NVDD15 + AVDD. Analog Supply Pins FPMVDD MPLLVDD OSC26VDD UPLLVDD OSC32VDD OSC32VSS FPMVSS MPLLVSS OSC26VSS UPLLVSS Supply for analog blocks
Quiet GND for analog blocks
QVDD Internal Power Supply QVDD QVSS Power supply pins for silicon internal circuitry GND pins for silicon internal circuitry
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 34 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Signal Descriptions
Table 3. i.MX27/MX27L Signal Descriptions (continued)
Pad Name FUSEVDD RTCVDD RTCVSS For FuseVDD For RTC, SCC power supply For RTC, SCC GND Function/Notes
Note: Both 1-Wire and Fast Ethernet Controller signals are multiplexed with other signals. As a result these signal names do not appear in this list. The signals are listed below with the named signal that they are multiplexed. 1-Wire Signals: The 1-Wire input and output signal is multiplexed with JTAG RTCK pad, PE16. Fast Ethernet Controller (FEC) Signals on the i.MX27. The ATA module does not exist on the i.MX27L: FEC_TX_EN: Transmit enable signal, through GPIO multiplexed with ATA_DATA15 pad; PF23 FEC_TX_ER: Transmit Data Error; through GPIO multiplexed with ATA_DATA14 pad; PD16 FEC_COL: Collision signal; through GPIO multiplexed with ATA_DATA13 pad; PD15 FEC_RX_CLK: Receive Clock signal; through GPIO multiplexed with ATA_DATA12 pad; PD14 FEC_RX_DV: Receive data Valid signal; through GPIO multiplexed with ATA_DATA11 pad; PD13 FEC_RXD0: Receive Data0; through GPIO multiplexed with ATA_DATA10 pad; PD12 FEC_TX_CLK: Transmit Clock signal; through GPIO multiplexed with ATA_DATA9 pad; PD11 FEC_CRS: Carrier Sense enable; through GPIO multiplexed with ATA_DATA8 pad; PD10 FEC_MDC: Management Data Clock; through GPIO multiplexed with ATA_DATA7 pad; PD9 FEC_MDIO: Management Data Input/Output, multiplexed with ATA_DATA6 pad; PD8 FEC_RXD3-1: Receive Data; through GPIO multiplexed with ATA_DATA5-3 pad; PD7-5 FEC_RX_ER: Receive Data Error; through GPIO multiplexed with ATA_DATA2 pad; PD4 FEC_TXD3-2: Transmit Data; through GPIO multiplexed with ATA_DATA1-0; pad; PD3-2 FEC_TXD1: Transmit Data; through GPIO multiplexed with SD3_CLK pad; PD1 FEC_TXD0: Transmit Data; through GPIO multiplexed with SD3_CMD pad; PD0 Note: The Rest ATA signals are multiplexed with PCMCIA Pads.
3.1
Power-Up Sequence
The i.MX27/MX27L processor consists of three major sets for power supply voltage named QVDD (core logic supply), FUSEVDD (analog supply for FUSEBOX), and NVDD VDDA (IO supply). The External Voltage Regulators and power-on devices must provide the applications processor with a specific sequence of power and resets to ensure proper operation. It is important that the applications processor power supplies be powered-up in a certain order to avoid unintentional fuse blown. QVDD should be powered up before FUSEVDD. The recommended order is: 1. QVDD(1.5 V) 2. FUSEVDD (1.8 V) NVDD (1.8/2.775 V), and Analog Supplies (2.775 V). See Table 3 for signal descriptions. or 1. QVDD (1.5 V), NVDD (1.8/2.775 V), and Analog Supplies (2.775 V). See Table 3 for signal descriptions. 2. FUSEVDD (1.8 V).
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 35
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Signal Descriptions
3.2
EMI Pins Multiplexing
This section discusses the multiplexing of EMI signals. The EMI signals' multiplexing is done inside the EMI. Table 4 lists the i.MX27 pin names, pad types, and the memory devices' equivalent pin names.
Table 4. EMI Multiplexing
Pin Name A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 MA10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 SDBA1 SDBA0 SD0 SD1 Pad Type regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular ddr ddr WEIM A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 -- A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 -- -- -- -- SDRAM MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 -- MA10 MA11 MA12 MA13 -- -- -- -- -- -- -- -- -- -- -- -- SDBA1 SDBA0 SD0 SD1 PCMCIA A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 -- A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 CE1 CE2 -- -- DDR MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 -- MA10 MA11 MA12 MA13 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- NFC -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 36 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Signal Descriptions
Table 4. EMI Multiplexing (continued)
Pin Name SD2 SD3 SD4 SD5 SD6 SD7 SD8 SD9 SD10 SD11 SD12 SD13 SD14 SD15 SD16 SD17 SD18 SD19 SD20 SD21 SD22 SD23 SD24 SD25 SD26 SD27 SD28 SD29 SD30 SD31 DQM0 DQM1 DQM2 DQM3 EB0 Pad Type ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr ddr regular WEIM -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- EB0 SDRAM SD2 SD3 SD4 SD5 SD6 SD7 SD8 SD9 SD10 SD11 SD12 SD13 SD14 SD15 SD16 SD17 SD18 SD19 SD20 SD21 SD22 SD23 SD24 SD25 SD26 SD27 SD28 SD29 SD30 SD31 DQM0 DQM1 DQM2 DQM3 -- PCMCIA -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- REG DDR -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- NFC -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 37
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Signal Descriptions
Table 4. EMI Multiplexing (continued)
Pin Name EB1 OE CS0 CS1 CS2 CS3 CS4 CS5 ECB LBA BCLK RW RAS CAS SDWE SDCKE0 SDCKE1 SDCLK SDCLK SDQS0 SDQS1 SDQS2 SDQS3 NFWE NFRE NFALE NFCLE NFWP NFCE NFRB D15 D14 D13 D12 D11 Pad Type regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular -- ddr ddr ddr ddr regular regular regular regular regular regular regular regular regular regular regular regular WEIM EB1 OE CS0 CS1 CS2 CS3 CS4 CS5 ECB LBA BCLK RW -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- D15 D14 D13 D12 D11 SDRAM -- -- -- -- CSD0 CSD1 -- -- -- -- -- -- RAS CAS SDWE SDCKE0 SDCKE1 SDCLK -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- PCMCIA IORD IOWR -- -- -- -- -- -- -- OE -- WE -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- D15 D14 D13 D12 D11 DDR -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- SDQS0 SDQS1 SDQS2 SDQS3 -- -- -- -- -- -- -- -- -- -- -- -- NFC -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- WE RE ALE CLE WP CE R/B D15 D14 D13 D12 D11
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 38 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Signal Descriptions
Table 4. EMI Multiplexing (continued)
Pin Name D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 PC_CD1 PC_CD2 PC_WAIT PC_READY PC_PWRON PC_VS1 PC_VS2 PC_BVD1 PC_BVD2 PC_RST IOIS16 PC_RW PC_POE M_REQUEST M_GRANT Pad Type regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular regular WEIM D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- SDRAM -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- PCMCIA D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 CD1 CD2 WAIT READY PC_PWRON VS1 VS2 BVD1 BVD2 RST IOIS16/WP RW POE -- -- DDR -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- NFC D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 39
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
4
4.1
Electrical Characteristics
i.MX27/IMX27L Chip-Level Conditions
This section provides the chip-level and module-level electrical characteristics for the i.MX27/IMX27L.
This section provides the chip-level electrical characteristics for the IC. See Table 5 for a quick reference to the individual tables and sections.
Table 5. i.MX27/IMX27L Chip-Level Conditions
For these characteristics... Table 6, "DC Absolute Maximum Conditions" Table 7, "DC Operating Conditions" Table 9, "Interface Frequency" Table 10, "Frequency Definition for Power Consumption Measurement" Table 11, "Current Consumption" Section 4.1.3, "Test Conditions and Recommended Settings" Topic appears... on page 40 on page 40 on page 41 on page 42 on page 42 on page 43
Table 6 provides the DC absolute maximum operating conditions. CAUTION Stresses beyond those listed under Table 6 may cause permanent damage to device. These are stress ratings only. Functional operation of device at these or any other conditions beyond those indicated under "DC operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Table 6. DC Absolute Maximum Conditions
Ref. Num 1 2 3 4 Supply Voltage Supply Voltage (Level Shift I/O) Input Voltage Range Storage Temperature Range Parameter Symbol VDDmax VDDIOmax VImax Tstorage Min -0.5 -0.5 -0.5 -20 Max 1.52 3.3 NVDD (1, 5-13) + 0.3 125 Units V V V
oC
Table 7 provides the DC recommended operating conditions.
Table 7. DC Operating Conditions
ID 1 2 Parameter Core Supply Voltage (@266 MHz) Core Supply Voltage (@400 MHz) Symbol QVDD QVDD Min 1.2 1.38 Typical 1.3 1.45 Max 1.52 1.52 Units V V
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 40 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 7. DC Operating Conditions (continued)
ID 3 4 5 Parameter RTC, SCC separate Supply Voltage I/O Supply Voltage, Fast (7, 11, 12, 14, 15)1 I/O Supply Voltage, Slow (5, 6, 8, 9, 10, 13, AVDD) Symbol RTC VDD NVDD_FAST NVDD_SLOW NVDD_SLOW 6 7 8 9 10 11 12 13 Note:
1 2
Min 1.2 1.75 1.75 1.75 1.75 1.35 1.7 3.00 1.1 2.68 -20 -40
Typical -- -- -- -- -- 1.4 1.875 3.15 -- -- -- --
Max 1.52 2.8 3.05 3.1 1.9 1.6 1.95 3.30 1.6 2.875 85 85
Units V V V V V V V V V V
oC oC
I/O Supply Voltage, DDR (1, 2, 3, 4)2 Analog Supply Voltage: FPMVDD, UPLLVDD, MPLLVDD Fusebox read Supply Voltage Fusebox Program Supply Voltage OSC32VDD OSC26VDD Operating Ambient Temperature (17mm x17mm package) Operating Ambient Temperature (19mm x19mm package)
NVDD_DDR VDD FUSEVDD (read mode) FUSEVDD (program mode) VOSC32 VOSC26 TA TA
Segments 11, 14, 15 are mixture of Fast and Slow GPIO. Segments 1, 3, 4 are mixture of DDR and Fast GPIO.
4.1.1
DPLL Frequency Specification
Table 8. DPLL FREQUENCY Specifications
Parameter Output Duty Cycle (dpdck) Output Duty Cycle (dpgdck_2) Frequency lock time (FOL mode or non-integer MF) Phase lock time Cycle-to-cycle jitter Min 48.5 48.5 -- Typical 50.0 50.0 -- Max 51.5 51.5 80 Unit % % s
Table 8 provides the frequency specifications for the DPLL.
-- --
-- --
100 0.2
s ns
Table 9 provides information for interface frequency limits.
Table 9. Interface Frequency
ID 1 Parameter JTAG: TCK Frequency of Operation Symbol fJTAG Min DC Typical 5 Max 33.25 Units MHz
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 41
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
4.1.2
Current Consumption
Table 10 defines the frequency settings used for specifying power consumption in Table 11. All power states are specified. The temperature setting of 25 C is used for specifying the Deep Sleep Mode (DSM) per the temperature range shown in Table 7.
Table 10. Frequency Definition for Power Consumption Measurement
ID 1 2 3 4 5 MCU core MCU core MCU AHB bus MCU IP bus OSC32 Parameter Symbol fMCUmeas@266 fMCUmeas@400 fMCU-AHBmeas fMCU-IPmeas fosc32khzmeas Value 266 400 133 66 32.768 Units MHz MHz MHz MHz kHz
Table 11 shows the power consumption for the i.MX27/IMX27L device.
Table 11. Current Consumption
ID 1 Parameter Conditions Symbol IddRUN IddRUN IddDOZE Typical 215 Max 260 Units mA
RUN Current RUN Current at 266 MHz (QVDD current) QVDD = 1.3 V. Ta = 25oC RUN Current at 400 MHz QVDD = 1.45 V, Ta = 25oC
366
420
mA
2
Doze Current
* * * * * * * * * * * * * * * * * * * *
QVDD = 1.2 V NVDD = 1.75 V ARM is in wait for interrupt mode. ARM well bias is enabled. MCU PLL is on. SPLL is off. FPM is on. 26MHz oscillator is on. 32 kHz oscillator is on. Other modules are off. TA = 25 C. QVDD = 1.2 V. NVDD = 1.75 V. Both PLLs are off. FPM is off. ARM well bias is enabled. 32 kHz oscillator is on. 26MHz oscillator is off. All the modules are off. TA = 25 C.
11
13.5
mA
3
Sleep Current
IddSLEEP
0.9
3.5
mA
4
Power Gate
* NVDD13 is on. See Table 7 for specific values. * RTCVDD, OSC32VDD are on. See Table 7 for specific values. * All other VDD = 0 V * TA = 25 C.
IddPG
50
TBD
A
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 42 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
4.1.3
Test Conditions and Recommended Settings
Unless specified, AC timing parameters are specified for 15 pF loading on i.MX27/IMX27L pads. Drive strength has been kept at default/reset values for testing. EMI timing has been verified with high drive strength setting and 25 pF loads. SDHC timing has also been verified with high drive strength setting. Unless otherwise noted, AC/DC parameters are guaranteed at operating conditions shown in Table 7.
4.2
Module-Level Electrical Specifications
This section contains the i.MX27/IMX27L electrical information including timing specifications, arranged in alphabetical order by module name.
4.2.1
4.2.1.1
Pads IO (PADIO) Electricals
DC Electrical Characteristics
The over-operating characteristics appear in Table 12 for GPIO pads and Table 13 for DDR (Double Data Rate) pads (unless otherwise noted).
Table 12. GPIO Pads DC Electrical Parameters
Parameter High-level output voltage Symbol VOH Test Conditions IOH = -1 mA IOH = specified Drive Low-level output voltage VOL IOL = 1 mA IOL = specified Drive High-level output current, slow slew rate IOH_S VOH = 0.8*NVDD Normal High Max High1 VOH = 0.8*NVDD Normal High Max High1 VOL = 0.2*NVDD Normal High Max High1 VOL = 0.2*NVDD Normal High Max High1 Hysteresis enabled Hysteresis enabled Hysteresis enabled Min NVDD -0.15 0.8*NVDD -- -- -2 -4 -8 -- -4 -6 -8 -- 2 4 8 -- 4 6 8 0.25 0.5*QVDD -- -- -- -- -- -- 0.5*QVDD V V V -- mA -- mA -- mA Typical -- -- -- -- -- Max -- -- 0.15 0.2*NVDD -- Units V V V V mA
High-level output current, fast slew rate
IOH_F
Low-level output current, slow slew rate
IOL_S
Low-level output current, fast slew rate
IOL_F
Input Hysteresis Schmitt trigger VT+ Schmitt trigger VT-
VHYS VT + VT -
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 43
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 12. GPIO Pads DC Electrical Parameters (continued)
Parameter Pull-up resistor (22 k PU) Pull-up resistor (47 k PU) Pull-up resistor (100 k PU) Pull-down resistor (100 k PD) Input current (no PU/PD) Input current (22 k PU) Input current (47 k PU) Input current (100 k PU) Input current (100 k PD) Tri-state input leakage current High Level DC Input Voltage Low-Level DC Input Voltage Note:
1
Symbol RPU RPU RPU RPD IIN IIN IIN IIN IIN IZ VIH VIL
Test Conditions -- -- -- -- VI = 0 VI = NVDD VI = 0 VI = NVDD VI = 0 VI = NVDD VI = 0 VI = NVDD VI = 0 VI = NVDD VI = NVDD or 0 I/O = high Z
-- --
Min 15 30 34 25 -- -- -- -- -- -- 0.7*VDDIO 0
Typical 22 47 100 100 0.33 -- -- -- -- 0.33 -- --
Max 59 128 268 343 1 115 0.1 53 0.1 25 0.1 0.25 28 2 VDDIO 0.3*VDDIO
Units
k
A A A A A A A A A A V V
Max High strength should be avoided due to excessive overshoot and ringing.
Table 13. DDR (Double Data Rate) I/O Pads DC Electrical Parameters
Parameter High-level output voltage Symbol VOH Test Conditions IOH = -1 mA IOH = specified Drive Low-level output voltage VOL IOL = 1 mA IOL = specified Drive High-level output current IOH VOH=0.8*NVDD_DDR Normal High Max High1 DDR Drive1 Min NVDD_DDR -0.08 0.8*NVDD_
DDR
Typical -- -- -- -- --
Max -- -- 0.08 0.2*NVDD_
DDR
Units V V V V mA
-- --
--
-3.6 -7.2 -10.8 -14.4
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 44 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 13. DDR (Double Data Rate) I/O Pads DC Electrical Parameters (continued)
Parameter Low-level output current Symbol IOL Test Conditions VOL=0.2*NVDD_DDR Normal High Max High1 DDR Drive1 VI = 0 VI = NVDD_DDR VI = NVDD_DDR or 0 I/O = high Z Min Typical -- 3.6 7.2 10.8 14.4 -- -- -- 1.7 1.7 2 2 2 A A A Max -- Units mA
Low-level input current High-level input current Tri-state current Note:
1
IIL IIH IZ
Max High and DDR Drive strengths should be avoided due to excessive overshoot and ringing.
4.2.1.2
AC Electrical Characteristics
Figure 2 depicts the load circuit for output pads. Figure 3 depicts the output pad transition time waveform. The range of operating conditions appear in Table 14 for slow general I/O, Table 15 for fast general I/O, and Table 16 for DDR I/O (unless otherwise noted).
From Output Under Test Test Point CL
CL includes package, probe and jig capacitance
Figure 2. Load Circuit for Output Pad
NVDD 80% Output (at pad) 20% PA1 PA1 80% 20% 0V
Figure 3. Output Pad Transition Time Waveform Table 14. AC Electrical Characteristics of Slow General I/O Pads
ID PA1 Parameter Output Pad Transition Times (Max High) Output Pad Transition Times (High) Output Pad Transition Times (Standard Drive) -- Note: Maximum Input Transition Times1 Symbol tpr tpr tpr trm Test Condition 25 pF 50 pF 25 pF 50 pF 25 pF 50 pF -- Min 1.25 1.95 1.45 2.6 2.6 5.1 -- Typical 1.9 2.9 -- -- -- Max 3.2 4.75 4.8 8.4 8.5 16.5 25 Units ns ns ns ns
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 45
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
1
Hysteresis mode is recommended for input with transition time greater than 25 ns.
Table 15. AC Electrical Characteristics of Fast General I/O Pads
ID PA1 Parameter Output Pad Transition Times (Max High) Output Pad Transition Times (High) Output Pad Transition Times (Normal) -- Note:
1
Symbol tpr tpr tpr trm
Test Condition 25 pF 50 pF 25 pF 50 pF 25 pF 50 pF --
Min 0.9 1.7 1.15 2.3 1.7 3.4 --
Typical 1.2 2.4 1.6 3.1 2.4 4.7 --
Max 2.0 4.0 2.7 5.3 4.0 8.0 25
Units ns ns ns ns
Maximum Input Transition Times1
Hysteresis mode is recommended for input with transition time greater than 25 ns.
Table 16. AC Electrical Characteristics of DDR I/O Pads
ID PA1 Parameter Output Pad Transition Times (DDR Drive) Output Pad Transition Times (Max High) Output Pad Transition Times (High) Output Pad Transition Times (Normal) -- Maximum Input Transition Times Symbol tpr tpr tpr tpr trm Test Condition 25 pF 50 pF 25 pF 50 pF 25 pF 35 pF 25 pF 50 pF -- Min 0.5 1.0 0.67 1.3 1.0 1.95 2.0 3.9 -- Typical 0.75 1.45 1.0 2.0 1.5 2.9 2.9 5.9 -- Max 1.2 2.4 1.6 3.1 2.4 4.7 4.8 8.4 5 Units ns ns ns ns ns
4.2.2
1-Wire Electrical Specifications
1-Wire Tx "Reset Pulse" DS2502 Tx "Presence Pulse" OW2
Figure 4 depicts the RPP timing, and Table 17 lists the RPP timing parameters.
One-Wire bus (BATT_LINE)
OW1
OW3 OW4
Figure 4. Reset and Presence Pulses (RPP) Timing Diagram
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 46 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 17. RPP Sequence Delay Comparisons Timing Parameters
ID OW1 OW2 OW3 OW4 Parameters Reset Time Low Presence Detect High Presence Detect Low Reset Time High Symbol tRSTL tPDH tPDL tRSTH Min 480 15 60 480 Typical 511 -- -- 512 60 240 -- Max Units s s s --
Figure 5 depicts Write 0 Sequence timing, and Table 18 lists the timing parameters.
OW6 One-Wire bus (BATT_LINE)
OW5
Figure 5. Write 0 Sequence Timing Diagram Table 18. WR0 Sequence Timing Parameters
ID OW5 OW6 Parameter Write 0 Low Time Transmission Time Slot Symbol tWR0_low tSLOT Min 60 OW5 Typical 100 117 Max 120 120 Units s s
Figure 6 depicts Write 1 Sequence timing, Figure 7 depicts the Read Sequence timing, and Table 19 lists the timing parameters.
OW8 One-Wire bus (BATT_LINE)
OW7
Figure 6. Write 1 Sequence Timing Diagram
OW8 One-Wire bus (BATT_LINE)
OW7 OW9
Figure 7. Read Sequence Timing Diagram
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 47
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 19. Write 1/Read Timing Parameters
ID OW7 OW8 OW9 Parameter Write 1/Read Low Time Transmission Time Slot Release Time Symbol tLOW1 tSLOT tRELEASE Min 1 60 15 Typical 5 117 -- Max 15 120 45 Units s s s
4.2.3
ATA Electrical Specifications
This section describes the electrical information of the Parallel ATA module compliant with ATA/ATAPI-6 specification. NOTE The parallel ATA module is not available on the i.MX27L Parallel ATA module can work on PIO/Multi-Word DMA/Ultra DMA transfer modes. Each transfer mode has different data transfer rate, Ultra DMA mode 4 data transfer rate is up to 100 MB/s. Parallel ATA module interface consist of a total of 29 pins, Some pins act on different function in different transfer mode. There are different requirements of timing relationships among the function pins conform with ATA/ATAPI-6 specification and these requirements are configurable by the ATA module registers. Below defines the AC characteristics of all the interface signals on all data transfer modes.
4.2.3.1
General Timing Requirements
Table 20. AC Characteristics of All Interface Signals
These are the general timing requirements for the ATA interface signals.
ID SI1 SI2 SI3
Parameter Rising edge slew rate for any signal on ATA interface (see note) Falling edge slew rate for any signal on ATA interface (see note) Host interface signal capacitance at the host connector
Symbol Srise Sfall Chost
Min -- -- --
Max 1.25 1.25 20
Unit V/ns V/ns pF
Note: SRISE and SFALL meets this requirement when measured at the sender's connector from 10-90% of full signal amplitude with all capacitive loads from 15 pf through 40 pf where all signals have the same capacitive load value.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 48 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
ATA Interface Signals
SI2
SI1
Figure 8. ATA interface Signals Timing Diagram
4.2.4
Digital Audio Mux (AUDMUX)
The AUDMUX provides a programmable interconnect logic for voice, audio and data routing between internal serial interfaces (SSI, SAP) and external serial interfaces (audio and voice codecs). The AC timing of AUDMUX external pins is hence governed by SSI and SAP modules. Please refer to their respective electrical specifications.
4.2.5
CMOS Sensor Interface (CSI)
This section describes the electrical information (AC timing) of the CSI.
4.2.5.1
Gated Clock Mode Timing
VSYNC, HSYNC, and PIXCLK signals are used in this mode. A frame starts with a rising/falling edge on VSYNC, then HSYNC goes high and holds for the entire line. The pixel clock is valid as long as HSYNC is high. Figure 9 and Figure 10 depict the gated clock mode timings of CSI, and Table 21 lists the timing parameters.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 49
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Figure 9 shows sensor output data on the pixel clock falling edge. The CSI latches data on the pixel clock rising edge.
1
VSYNC
7
HSYNC
2
5
6
PIXCLK
DATA[7:0] 3
Valid Data 4
Valid Data
Valid Data
Figure 9. CSI Timing Diagram, Gated, PIXCLK--Sensor Data at Falling Edge, Latch Data at Rising Edge
Figure 10 shows sensor output data on the pixel clock rising edge. The CSI latches data on the pixel clock falling edge.
1
VSYNC
7
HSYNC
2
5
6
PIXCLK
DATA[7:0]
Valid Data
Valid Data
Valid Data
3
4
Figure 10. CSI Timing Diagram, Gated, PIXCLK--Sensor Data at Rising Edge, Latch Data at Falling Edge
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 50 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 21. Gated Clock Mode Timing Parameters
Number 1 2 3 4 5 6 7 Parameter csi_vsync to csi_hsync csi_hsync to csi_pixclk csi_d setup time csi_d hold time csi_pixclk high time csi_pixclk low time csi_pixclk frequency Minimum 9*THCLK 3 1 1 THCLK THCLK 0 Maximum -- (Tp/2)-3 -- -- -- -- HCLK/2 Unit ns ns ns ns ns ns MHz
HCLK = AHB System Clock, THCLK = Period for HCLK, Tp = Period of CSI_PIXCLK The limitation on pixel clock rise time/fall time is not specified. It should be calculated from the hold time and setup time based on the following assumptions: Rising-edge latch data: max rise time allowed = (positive duty cycle--hold time) max fall time allowed = (negative duty cycle--setup time) In most of case, duty cycle is 50/50, therefore: max rise time = (period/2--hold time) max fall time = (period/2--setup time) For example: Given pixel clock period = 10 ns, duty cycle = 50/50, hold time = 1 ns, setup time = 1 ns. positive duty cycle = 10/2 = 5 ns max rise time allowed = 5 -1 = 4 ns negative duty cycle = 10/2 = 5 ns max fall time allowed = 5 -1 = 4 ns Falling-edge latch data: max fall time allowed = (negative duty cycle--hold time) max rise time allowed = (positive duty cycle--setup time)
4.2.5.2
Non-Gated Clock Mode Timing
In non-gated mode only, the VSYNC, and PIXCLK signals are used; the HSYNC signal is ignored. Figure 3 and Figure 4 show the different clock edge timing of CSI and Sensor in Non-Gated Mode. Table 3 is the parameter value. Figure 11 and Figure 12 show the non-gated clock mode timings of CSI, and Table 22 lists the timing parameters.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 51
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Figure 11 shows sensor output data on the pixel clock falling edge. The CSI latches data on the pixel clock rising edge.
1
VSYNC 6 4 5
PIXCLK
DATA[7:0] 2
Valid Data
Valid Data
Valid Data
3
Figure 11. CSI Timing Diagram, Non-Gated, PIXCLK--Sensor Data at Falling Edge, Latch Data at Rising Edge
Figure 12 shows sensor output data on the pixel clock rising edge. The CSI latches data on the pixel clock falling edge.
1
VSYNC 5
6 4
PIXCLK
DATA[7:0] 2
Valid Data 3
Valid Data
Valid Data
Figure 12. CSI Timing Diagram, Non-Gated, PIXCLK--Sensor Data at Rising Edge, Latch Data at Falling Edge Table 22. Non-Gated Clock Mode Parameters
Number -- -- Parameter csi_vsync to csi_pixclk csi_d setup time Minimum 9*THCLK 1 Maximum -- -- Unit ns ns
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 52 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 22. Non-Gated Clock Mode Parameters (continued)
Number -- -- -- -- Parameter csi_d hold time csi_pixclk high time csi_pixclk low time csi_pixclk high time Minimum 1 THCLK THCLK 0 Maximum -- -- -- HCLK/2 Unit ns ns ns MHz
HCLK = AHB System Clock, THCLK = Period of HCLK
4.2.6
Configurable Serial Peripheral Interface (CSPI)
This section describes the electrical information of the CSPI.
4.2.6.1
CSPI Timing
Figure 13 and Figure 14 show the master mode and slave mode timings of CSPI, and Table 23 lists the timing parameters.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 53
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
4.3
Timing Diagrams
Figure 13 and Figure 14 depict the master mode and slave mode timing diagrams of the CSPI and Table 23 lists the timing parameters. The values shown in timing diagrams were tested using a worst case core voltage of 1.1 V, slow pad voltage of 2.68 V, and fast pad voltage of 1.65 V.
t7 SSn (output) t8
t9
t5
t6 CSPI1_RDY (input) SCLK (output) MOSI t12 MISO t13 t1 t2 t3
t10
t11 t4 t4
Figure 13. CSPI Master Mode Timing Diagram
t7' SSn (Input) t6' t1' SCLK (Input) t2' t3' t5'
t10
t11 t4 t4
MISO t12 MOSI t13
Figure 14. CSPI Slave Mode Timing Diagram
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 54 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 23. CSPI Interface Timing Parameters
ID Num t1 t2 t3 t1' t2' t3' t4 t5 t5' t6 t6' t7 t7' t8 t9 t10 Parameter Description CSPI master SCLK cycle time CSPI master SCLK high time CSPI master SCLK low time CSPI slave SCLK cycle time CSPI slave SCLK high time CSPI slave SCLK low time CSPI SCLK transition time SSn output pulse width SSn input pulse width SSn output asserted to first SCLK edge (SS output setup time) SSn input asserted to first SCLK edge (SS input setup time) CSPI master: Last SCLK edge to SSn deasserted (SS output hold time) CSPI slave: Last SCLK edge to SSn deasserted (SS input hold time) CSPI master: CSPI1_RDY low to SSn asserted (CSPI1_RDY setup time) CSPI master: SSn deasserted to CSPI1_RDY low Output data setup time Symbol tclko tclkoH tclkoL tclki tclkiH tclkiL tpr1 tWsso tWssi tSsso tSssi tHsso tHssi tSrdy tHrdy tSdatao Minimum 45.12 22.65 22.47 60.2 30.1 30.1 2.6 2Tsclk2 +T wait3 Maximum -- -- -- -- -- 8.5 -- -- -- -- -- -- 5Tper -- -- Units ns ns ns ns ns ns ns -- -- -- -- -- ns -- ns --
Tper4 3T sclk Tper + 20 ns 2T sclk 30 2Tper 0 (tclkoL or tclkoH or tclkiL or tclkiH) Tipg5 tclkoL or tclkoH or tclkiL or tclkiH Tipg + 0.5 5
t11 t12 t13 Note:
Output data hold time Input data setup time Input data hold time
tHdatao tSdatai tHdatai
-- -- --
-- ns ns
The output SCLK transition time is tested with 25 pF drive. Tsclk = CSPI clock period 3 Twait = Wait time as per the Sample Period Control Register value. 4T per = CSPI reference baud rate clock period (PERCLK2) 5T ipg = CSPI main clock IPG_CLOCK period
2
1
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 55
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
4.3.1
Direct Memory Access Controller (DMAC)
After assertion of External DMA Request the DMA burst will start when the corresponding DMA channel becomes the current highest priority channel. The External DMA Request should be kept asserted until it is serviced by the DMAC. One External request will initiate at least one DMA burst. The output External Grant signal from the DMAC is an active-low signal. This signal will be asserted during the time when a DMA burst is ongoing for an External DMA Request, when the following conditions are true: * The DMA channel for which the DMA burst is ongoing has requested source as external DMA Request (as per RSSR settings). * REN and CEN bit of this channel are set. * External DMA Request is asserted. Once the grant is asserted the External DMA Request will not be sampled until completion of the DMA burst. The priority of the external request will become low, for the next consecutive burst, if another DMA request signal is asserted. The waveforms are shown for the worst case--that is, smallest burst (1 byte read/write). Minimum and maximum timings for the External request and External grant signal are present in the data sheet. Figure 15 shows the minimum time for which the External Grant signal remains asserted if External DMA request is de-asserted immediately after sensing grant signal active.
Ext_DMAReq
Ext_DMAGrant
tmin_assert
Figure 15. Assertion of DMA External Grant Signal
Figure 16 shows the safe maximum time for which External DMA request can be kept asserted, after sensing grant signal active such that a new burst is not initiated.
Ext_DMAReq
Ext_DMAGrant tmax_req_assert Data read from External device Data written to External device tmax_read tmax_write
NOTE: Assuming worst case that the data is read/written from/to external device as per the above waveform.
Figure 16. Timing Diagram of Safe Maximums for External Request De-Assertion
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 56 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 24. DMAC Timing Parameters
3.0 V Parameter Description WCS Tmin_assert Minimum assertion time of External Grant signal 8hclk+8.6 9hclk-20.66 8hclk-6.21 3hclk-5.87 BCS 8hclk+2.74 9hclk-6.7 8hclk-0.77 3hclk-8.83 WCS 8hclk+7.17 9hclk-17.96 8hclk-5.84 3hclk-15.9 BCS 8hclk+3.25 9hclk-8.16 8hclk-0.66 3hclkv91.2 ns ns ns ns 1.8 V Unit
Tmax_req_assert Maximum External Request assertion time after assertion of Grant signal Tmax_read Tmax_write Maximum External Request assertion time after first read completion Maximum External Request assertion time after first write completion
4.3.2
Fast Ethernet Controller (FEC)
This section describes the AC timing specifications of the FEC. The MII signals are compatible with transceivers operating at a voltage of 3.3 V.
4.3.2.1
MII Receive Signal Timing (FEC_RXD[3:0], FEC_RX_DV, FEC_RX_ER, and FEC_RX_CLK)
The receiver functions correctly up to a FEC_RX_CLK maximum frequency of 25 MHz + 1%. There is no minimum frequency requirement. In addition, the FEC IPG clock frequency must exceed twice the FEC_RX_CLK frequency. Figure 17 shows the MII receive signal timings, and Table 25 lists the timing parameters.
M3
FEC_RX_CLK (input)
M4 FEC_RXD[3:0] (inputs) FEC_RX_DV FEC_RX_ER M1 M2
Figure 17. MII Receive Signal Timing Diagram Table 25. MII Receive Signal Timing Parameters
ID M1 M2 M3 Parameter1 FEC_RXD[3:0], FEC_RX_DV, FEC_RX_ER to FEC_RX_CLK setup FEC_RX_CLK to FEC_RXD[3:0], FEC_RX_DV, FEC_RX_ER hold FEC_RX_CLK pulse width high Min 5 5 35% Max -- -- 65% Unit ns ns FEC_RX_CLK period
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 57
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 25. MII Receive Signal Timing Parameters (continued)
ID M4 Note:
1
Parameter1 FEC_RX_CLK pulse width low
Min 35%
Max 65%
Unit FEC_RX_CLK period
FEC_RX_DV, FEC_RX_CLK, and FEC_RXD0 have the same timing in 10 Mbps 7-wire interface mode.
4.3.2.2
MII Transmit Signal Timing (FEC_TXD[3:0], FEC_TX_EN, FEC_TX_ER, and FEC_TX_CLK)
The transmitter functions correctly up to a FEC_TX_CLK maximum frequency of 25 MHz + 1%. There is no minimum frequency requirement. In addition, the FEC IPG clock frequency must exceed twice the FEC_TX_CLK frequency. Figure 18 shows the MII transmit signal timings, and Table 26 lists the timing parameters.
M7
FEC_TX_CLK (input) M5 FEC_TXD[3:0] (outputs) FEC_TX_EN FEC_TX_ER M6
M8
Figure 18. MII Transmit Signal Timing Diagram Table 26. MII Transmit Signal Timing Parameters
ID M5 M6 M7 M8 Note:
1
Parameter1 FEC_TX_CLK to FEC_TXD[3:0], FEC_TX_EN, FEC_TX_ER invalid FEC_TX_CLK to FEC_TXD[3:0], FEC_TX_EN, FEC_TX_ER valid FEC_TX_CLK pulse width high FEC_TX_CLK pulse width low
Min 5 -- 35% 35%
Max -- 20 65% 65%
Unit ns ns FEC_TX_CLK period FEC_TX_CLK period
FEC_TX_EN, FEC_TX_CLK, and FEC_TXD0 have the same timing in 10 Mbps 7-wire interface mode.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 58 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
4.3.2.3
MII Asynchronous Inputs Signal Timing (FEC_CRS and FEC_COL)
Figure 19 shows the MII asynchronous input timings, and Table 27 lists the timing parameters.
FEC_CRS, FEC_COL M9
Figure 19. MII Asynchronous Inputs Signal Timing Diagram Table 27. MII Asynchronous Inputs Signal Timing Parameter
ID M91 Note:
1
Parameter FEC_CRS to FEC_COL minimum pulse width
Min 1.5
Max --
Unit FEC_TX_CLK period
FEC_COL has the same timing in 10 Mbit 7-wire interface mode.
4.3.2.4
MII Serial Management Channel Timing (FEC_MDIO and FEC_MDC)
The FEC functions correctly with a maximum MDC frequency of 2.5 MHz. The MDC frequency should be equal to or less than 2.5 MHz to be compliant with IEEE 802.3 MII specification. However the FEC can function correctly with a maximum MDC frequency of 15 MHz. Figure 20 shows the MII serial management channel timings, and Table 28 lists the timing parameters.
M14 M15 FEC_MDC (output)
M10
FEC_MDIO (output)
M11
FEC_MDIO (input)
M12
M13
Figure 20. MII Serial Management Channel Timing Diagram
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 59
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 28. MII Serial Management Channel Timing Parameters
ID M10 M11 M12 M13 M14 M15 Parameter FEC_MDC falling edge to FEC_MDIO output invalid (minimum propagation delay) FEC_MDC falling edge to FEC_MDIO output valid (max propagation delay) FEC_MDIO (input) to FEC_MDC rising edge setup FEC_MDIO (input) to FEC_MDC rising edge hold FEC_MDC pulse width high FEC_MDC pulse width low Min Max 0 -- 18 0 -- 5 -- -- Unit ns ns ns ns FEC_MDC period FEC_MDC period
40% 60% 40% 60%
4.3.3
Inter IC Communication (I2C)
This section describes the electrical information of the I2C module.
4.3.3.1
I2C Module Timing
The I2C communication protocol consists of seven elements: START, Data Source/Recipient, Data Direction, Slave Acknowledge, Data, Data Acknowledge, and STOP. Figure 21 shows the timing of the I2C module. Table 29 lists the I2C module timing parameters.
SDA
IC5 IC3 IC4 SCL IC1 IC2 IC6
2
Figure 21. I C Bus Timing Diagram Table 29. I2C Module Timing Parameters
1.8 V +/-0.10 V ID Parameter Min -- IC1 IC2 IC3 IC4 IC5 IC6 SCL Clock Frequency Hold time (repeated) START Condition Data Hold Time Data Setup Time HIGH period of the SCL clock LOW period of the SCL clock Setup Time for STOP condition 0 114.8 0 3.1 69.7 336.4 110.5 Max 100 -- 69.7 -- -- -- -- Min 0 111.1 0 1.76 68.3 335.1 111.1 Max 100 -- 72.3 -- -- -- -- kHz ns ns ns ns ns ns 3.0 V +/-0.30 V Unit
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 60 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
4.3.4
JTAG Controller (JTAGC)
This section details the electrical characteristics for the JTAGC module. Figure 22 shows the JTAGC test clock input timing; Figure 23 shows the JTAGC boundary scan timing; Figure 24 shows the JTAGC test access port; Figure 25 shows the JTAGC TRST timing; and Table 30 lists the JTAGC timing parameters.
J1 J2 Tck (input) J3 J3 J2
Figure 22. Test Clock Input Timing Diagram
TCK (input) J5 J4 Data (inputs) J6 Data (outputs) Output Data Valid Input Data Valid
J7 Data (outputs)
J6 Data (outputs) Output Data Valid
Figure 23. Boundary Scan Timing Diagram
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 61
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
TCK (input) J9 J8 TDI, TMS (inputs) J10 TD0 (outputs) Output Data Valid Input Data Valid
J11 TD0 (outputs)
J10 TD0 (outputs) Output Data Valid
Figure 24. Test Access Port (TAP) Diagram
TCK (input) J13 TRST (input) J12
Figure 25. TRST Timing Diagram Table 30. JTAGC Timing Parameters
All Frequencies ID Parameter Min J1 J2 J3 J4 J5 TCK cycle time in crystal mode TCK clock pulse width measured at TCK rise and fall times Boundary scan input data set-up time Boundary scan input data hold time VM1 30.08 15.04 -- 3.5 16.0 Max -- -- 2.0 -- -- ns ns ns ns ns Unit
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 62 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 30. JTAGC Timing Parameters (continued)
All Frequencies ID Parameter Min J6 J7 J8 J9 J10 J11 J12 J13 Note:
1
Unit Max 25.0 25.0 -- -- 29.0 29.0 -- -- ns ns ns ns ns ns ns ns
TCK low to output data valid TCK low to output high impedance TMS, TDI data set-up time TMS, TDI data hold time TCK low to TDO data valid TCK low to TDO high impedance TRST assert time TRST set-up time to TCK low
-- -- 3.5 20.0 -- -- 70.0 2.5.0
Midpoint voltage
4.3.5
Liquid Crystal Display Controller Module (LCDC)
Figure 26 and Figure 27 depict the timings of the LCDC, and Table 31 and Table 32 list the timing parameters.
T5
FLM
Line n Line 1
LP
Line 1
Line 2
T2
LP
T1 T6
LSCLK
T3 T4
LD
Figure 26. LCDC Non-TFT Mode Timing Diagram
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 63
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 31. LCDC Non-TFT Mode Timing Parameters
ID T1 T2 T3 T4 T5 T6 Note:
1
Description Pixel Clock period LP width LD setup time LD hold time Wait between LP and FLM rising edge Wait between last data and LP rising edge
Min 22.5 1 5 5 2 1
Max 1000 -- -- -- -- --
Unit ns T1 ns ns T1 T1
T is pixel clock period.
VSYNC
HSYNC
Line 1
Line 2
Line n
Line 1
HSYNC T2 T5 T6
OE T1 LSCLK T3 LD T4
Figure 27. LCDC TFT Mode Timing Diagram Table 32. LCDC TFT Mode Timing Parameters
ID T1 T2 T3 T4 T5 T6 Description Pixel Clock period HSYNC width LD setup time LD hold time Delay from the end of HSYNC to the beginning of the OE pulse. Delay from end of OE to the beginning of the HSYNC pulse. Min 22.5 1 5 5 3 1 Ma 1000 -- -- -- -- -- Unit ns T1 ns ns T1 T1
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 64 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
1
T is pixel clock period.
4.3.6
Memory Stick Host Controller (MSHC)
Figure 30, Figure 28, and Figure 29 show the MSHC timings. Table 33 and Table 34 list the timing parameters. NOTE The i.MX27L does not contain an MSHC module.
tSCLKc
MSHC_SCLK
tBSsu
tBSh
MSHC_BS
tDsu MSHC_DATA (Output)
tDh
tDd MSHC_DATA (Input)
Figure 28. Transfer Operation Timing Diagram (Serial)
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 65
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
tSCLKc
MSHC_SCLK
tBSsu
tBSh
MSHC_BS
tDsu MSHC_DATA (Output)
tDh
tDd MSHC_DATA (Input)
Figure 29. Transfer Operation Timing Diagram (Parallel)
tSCLKc tSCLKwh tSCLKwl
MSHC_SCLK tSCLKr tSCLKf
Figure 30. MSHC_CLK Timing Diagram Table 33. Serial Interface Timing Parameters
Standards Signal Parameter Symbol Min. MSHC_SCLK Cycle H pulse length L pulse length Rise time Fall time tSCLKc tSCLKwh tSCLKwl tSCLKr tSCLKf 50 15 15 -- -- Max. -- -- -- 10 10 ns ns ns ns ns Unit
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 66 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 33. Serial Interface Timing Parameters (continued)
Standards Signal Parameter Symbol Min. MSHC_BS Setup time Hold time MSHC_DATA Setup time Hold time Output delay time tBSsu tBSh tDsu tDh tDd 5 5 5 5 -- Max. -- -- -- -- 15 ns ns ns ns ns Unit
Table 34. Parallel Interface Timing Parameters
Standards Signal Parameter Symbol Min MSHC_SCLK Cycle H pulse length L pulse length Rise time Fall time MSHC_BS Setup time Hold time MSHC_DATA Setup time Hold time Output delay time tSCLKc tSCLKwh tSCLKwl tSCLKr tSCLKf tBSsu tBSh tDsu tDh tDd 25 5 5 -- -- 8 1 8 1 -- Max -- -- -- 10 10 -- -- -- -- 15 ns ns ns ns ns ns ns ns ns ns Unit
4.3.7
NAND Flash Controller Interface (NFC)
Figure 31, Figure 32, Figure 33, and Figure 34 show the relative timing requirements among different signals of the NFC at module level, and Table 35 lists the timing parameters. The NAND Flash Controller (NFC) timing parameters are based on the internal NFC clock generated by the Clock Controller module, where time T is the period of the NFC clock in ns. The relationship between the NFC clock and the external timing parameters of the NFC is provided in Table 35. Table 35 also provides two examples of external timing parameters with NFC clock frequencies of 22.17 MHz and 33.25 MHz. Assuming a 266 MHz FCLK (CPU clock), NFCDIV should be set to divide-by-12 to generate a 22.17 MHz NFC clock and divide-by-8 to generate a 33.25 MHz NFC clock. The user should compare the parameters of the selected NAND Flash memory with the NFC external timing parameters to determine the proper NFC clock. The maximum NFC clock allowed is 66 MHz. It should also be noted that the default NFC clock on power up is 16.63 MHz.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 67
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
NFCLE
NF1 NF3
NF2 NF4
NFCE
NF5 NFWE NF6 NFALE NF7
NF8 NFIO[7:0] command
NF9
Figure 31. Command Latch Cycle Timing Diagram
NFCLE NF1 NFCE NF4 NF3
NF5 NFWE NF6 NF7 NFALE NF8 NFIO[7:0] Address
Time it takes for SW to issue the next address command
NF9 Address
Figure 32. Address Latch Cycle Timing Diagram
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 68 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
NFCLE NF1 NF3 NFCE
NF10 NF5 NFWE NF6 NFALE NF11
NF4
NF8 NFIO[15:0] Data to Flash
NF9
Figure 33. Write Data Latch Timing Diagram
NFCLE NFCE
NF3 NF13 NFRE
NF14 NF15
NF16 NFRB
NF17
NFIO[15:0] NF12
Data from Flash
Figure 34. Read Data Latch Timing Diagram Table 35. NFC Target Timing Parameters
Relationship to NFC NFC clock 22.17 MHz NFC clock 33.25 MHz clock period (T) T = 45 ns T = 30 ns Min NF1 NF2 NF3 NF4 NF5 NFCLE Setup Time NFCLE Hold Time NFCE Setup Time NFCE Hold Time NF_WP Pulse Width tCLS tCLH tCS tCH tWP T T T T T Max -- -- -- -- -- Min 45 45 45 45 45 Max -- -- -- -- -- Min 30 30 30 30 30 Max -- -- -- -- -- ns ns ns ns ns
ID
Parameter
Symbol
Unit
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 69
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 35. NFC Target Timing Parameters (continued)
Relationship to NFC NFC clock 22.17 MHz NFC clock 33.25 MHz clock period (T) T = 45 ns T = 30 ns Min NF6 NF7 NF8 NF9 NF10 NF11 NF12 NF13 NF14 NF15 NF16 NF17 NFALE Setup Time NFALE Hold Time Data Setup Time Data Hold Time Write Cycle Time NFWE Hold Time Ready to NFRE Low NFRE Pulse Width READ Cycle Time NFRE High Hold Time Data Setup on READ Data Hold on READ tALS tALH tDS tDH tWC tWH tRR tRP tRC tREH tDSR tDHR T T T T 2T T 4T 1.5T 2T 0.5T 15 0 Max -- -- -- -- -- -- -- -- -- -- -- -- Min 45 45 45 45 90 45 180 67.5 90 22.5 15 0 Max -- -- -- -- -- -- -- -- -- -- -- -- Min 30 30 30 30 60 30 120 45 60 15 15 0 Max -- -- -- -- -- -- -- -- -- -- -- -- ns ns ns ns ns ns ns ns ns ns ns ns
ID
Parameter
Symbol
Unit
NOTE High is defined as 80% of signal value and low is defined as 20% of signal value. All timings are listed according to this NFC clock frequency (multiples of NFC clock period) except NF16, which is not NFC clock related. The read data is generated by the NAND Flash device and sampled with the internal NFC clock.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 70 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
4.3.8
Personal Computer Memory Card International Association (PCMCIA)
Figure 35 and Figure 36 show the timings pertaining to the PCMCIA module, each of which is an example of one clock of strobe setup time and one clock of strobe hold time. Table 36 lists the timing parameters.
HCLK HADDR CONTROL HWDATA HREADY HRESP A[25:0] D[15:0] WAIT REG OE/WE/IORD/IOWR CE1/CE2 RD/WR POE REG OKAY ADDR 1 DATA write 1 OKAY OKAY ADDR 1 CONTROL 1 DATA write 1
PSST
PSL
PSHT
Figure 35. Write Accesses Timing Diagram--PSHT=1, PSST=1
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 71
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
HCLK HADDR CONTROL RWDATA HREADY HRESP A[25:0] D[15:0] WAIT REG OE/WE/IORD/IOWR CE1/CE2 RD/WR POE REG OKAY ADDR 1 OKAY OKAY ADDR 1 CONTROL 1 DATA read 1
PSST
PSL
PSHT
Figure 36. Read Accesses Timing Diagram--PSHT=1, PSST=1 Table 36. PCMCIA Write and Read Timing Parameters
Symbol PSHT PSST PSL Parameter PCMCIA strobe hold time PCMCIA strobe set up time PCMCIA strobe length Min 0 1 1 Max 63 63 128 Unit clock clock clock
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 72 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
4.3.9
SDRAM (DDR and SDR) Memory Controller
Figure 37, Figure 38, Figure 39, Figure 40, Figure 41, and Figure 42 depict the timings pertaining to the ESDCTL module, which interfaces Mobile DDR or SDR SDRAM. Table 37, Table 38, Table 39, Table 40, Table 41, and Table 42 list the timing parameters.
SD1 SDCLK SDCLK SD4 CS SD5 RAS SD4 SD2 SD3
SD5 CAS SD4
SD4 SD5 WE SD6 SD7 ADDR ROW/BA
SD5
COL/BA SD8 SD10 SD9 Data
DQ
DQM
SD4
Note: CKE is high during the read/write cycle.
SD5
Figure 37. SDRAM Read Cycle Timing Diagram Table 37. DDR/SDR SDRAM Read Cycle Timing Parameters
ID SD1 SD2 SD3 SD4 SD5 Parameter SDRAM clock high-level width SDRAM clock low-level width SDRAM clock cycle time CS, RAS, CAS, WE, DQM, CKE setup time CS, RAS, CAS, WE, DQM, CKE hold time Symbol tCH tCL tCK tCMS tCMH Min 3.4 3.4 7.5 2.0 1.8 Max 4.1 4.1 -- -- -- Unit ns ns ns ns ns
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 73
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 37. DDR/SDR SDRAM Read Cycle Timing Parameters (continued)
ID SD6 SD7 SD8 SD9 SD10 Note:
1
Parameter Address setup time Address hold time SDRAM access time Data out hold time1 Active to read/write command period
Symbol tAS tAH tAC tOH tRC
Min 2.0 1.8 -- 1.8 10
Max -- -- 6.47 -- --
Unit ns ns ns ns clock
Timing parameters are relevant only to SDR SDRAM. For the specific DDR SDRAM data related timing parameters, see Table 41 and Table 42.
NOTE SDR SDRAM CLK parameters are being measured from the 50% point--that is, high is defined as 50% of signal value and low is defined as 50% of signal value. SD1 + SD2 does not exceed 7.5 ns for 133 MHz. The timing parameters are similar to the ones used in SDRAM data sheets--that is, Table 37 indicates SDRAM requirements. All output signals are driven by the ESDCTL at the negative edge of SDCLK and the parameters are measured at maximum memory frequency.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 74 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics SD1 SDCLK SDCLK SD2 SD3 SD4 CS SD5 RAS SD11 CAS SD5 SD4 SD4
SD4
WE SD5 SD7 SD6 ADDR BA ROW / BA SD13 DQ DATA COL/BA SD12
SD5
SD14
DQM
Figure 38. SDR SDRAM Write Cycle Timing Diagram Table 38. SDR SDRAM Write Timing Parameters
ID SD1 SD2 SD3 SD4 SD5 SD6 SD7 SD11 SD12 Parameter SDRAM clock high-level width SDRAM clock low-level width SDRAM clock cycle time CS, RAS, CAS, WE, DQM, CKE setup time CS, RAS, CAS, WE, DQM, CKE hold time Address setup time Address hold time Precharge cycle period1 Active to read/write command delay1 Symbol tCH tCL tCK tCMS tCMH tAS tAH tRP tRCD Min 3.4 3.4 7.5 2.0 1.8 2.0 1.8 1 1 Max 4.1 4.1 -- -- -- -- -- 4 8 Unit ns ns ns ns ns ns ns clock clock
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 75
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 38. SDR SDRAM Write Timing Parameters (continued)
ID SD13 SD14 Note:
1
Parameter Data setup time Data hold time
Symbol tDS tDH
Min 2.0 1.3
Max -- --
Unit ns ns
SD11 and SD12 are determined by SDRAM controller register settings.
NOTE SDR SDRAM CLK parameters are being measured from the 50% point--that is, high is defined as 50% of signal value and low is defined as 50% of signal value. The timing parameters are similar to the ones used in SDRAM data sheets--that is, Table 38 indicates SDRAM requirements. All output signals are driven by the ESDCTL at the negative edge of SDCLK and the parameters are measured at maximum memory frequency.
SD1 SDCLK SDCLK SD2 SD3 CS
RAS SD11 CAS SD10 WE SD10
SD7 SD6 ADDR BA ROW/BA
Figure 39. SDRAM Refresh Timing Diagram Table 39. SDRAM Refresh Timing Parameters
ID SD1 SD2 Parameter SDRAM clock high-level width SDRAM clock low-level width Symbol tCH tCL Min 3.4 3.4 Max 4.1 4.1 Unit ns ns
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 76 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 39. SDRAM Refresh Timing Parameters (continued)
ID SD3 SD6 SD7 SD10 SD11 Note:
1
Parameter SDRAM clock cycle time Address setup time Address hold time Precharge cycle period1 Auto precharge command period1
Symbol tCK tAS tAH tRP tRC
Min 7.5 1.8 1.8 1 2
Max -- -- -- 4 20
Unit ns ns ns clock clock
SD10 and SD11 are determined by SDRAM controller register settings.
NOTE SDR SDRAM CLK parameters are being measured from the 50% point--that is, high is defined as 50% of signal value and low is defined as 50% of signal value. The timing parameters are similar to the ones used in SDRAM data sheets--that is, Table 39 indicates SDRAM requirements. All output signals are driven by the ESDCTL at the negative edge of SDCLK and the parameters are measured at maximum memory frequency.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 77
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
SDCLK CS
RAS
CAS
WE
ADDR
BA
CKE
SD16
SD16
Don't care
Figure 40. SDRAM Self-Refresh Cycle Timing Diagram
NOTE The clock continues to run unless both CKEs are low. Then the clock is stopped in low state.
Table 40. SDRAM Self-Refresh Cycle Timing Parameters
ID SD16 Parameter CKE output delay time Symbol tCKS Min 1.8 Max -- Unit ns
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 78 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
SDCLK SDCLK SD19 DQS (output) SD17 DQ (output) Data Data SD20
SD18
SD17 Data Data
SD18 Data Data Data Data
DQM (output) SD17
DM
DM
DM SD17
DM
DM SD18
DM
DM
DM
SD18
Figure 41. Mobile DDR SDRAM Write Cycle Timing Diagram Table 41. Mobile DDR SDRAM Write Cycle Timing Parameters1
ID SD17 SD18 SD19 SD20 Note:
1
Parameter DQ and DQM setup time to DQS DQ and DQM hold time to DQS Write cycle DQS falling edge to SDCLK output delay time. Write cycle DQS falling edge to SDCLK output hold time.
Symbol tDS tDH tDSS tDSH
Min 0.95 0.95 1.8 1.8
Max -- -- -- --
Unit ns ns ns ns
Test condition: Measured using delay line 5 programmed as follows: ESDCDLY5[15:0] = 0x0703.
NOTE SDRAM CLK and DQS related parameters are being measured from the 50% point--that is, high is defined as 50% of signal value and low is defined as 50% of signal value. The timing parameters are similar to the ones used in SDRAM data sheets--that is, Table 41 indicates SDRAM requirements. All output signals are driven by the ESDCTL at the negative edge of SDCLK and the parameters are measured at maximum memory frequency.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 79
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
SDCLK SDCLK SD23 DQS (input) SD22 SD21 DQ (input) Data Data Data Data Data Data Data Data
Figure 42. Mobile DDR SDRAM DQ versus DQS and SDCLK Read Cycle Timing Diagram Table 42. Mobile DDR SDRAM Read Cycle Timing Parameters
ID Parameter Symbol tDQSQ tQH tDQSCK Min -- 2.3 -- Max 0.85 -- 6.7 Unit ns ns ns
SD21 DQS-DQ Skew (defines the Data valid window in read cycles related to DQS). SD22 DQS DQ HOLD time from DQS SD23 DQS output access time from SDCLK posedge
NOTE SDRAM CLK and DQS related parameters are being measured from the 50% point--that is, high is defined as 50% of signal value and low is defined as 50% of signal value. The timing parameters are similar to the ones used in SDRAM data sheets--that is, Table 42 indicates SDRAM requirements. All output signals are driven by the ESDCTL at the negative edge of SDCLK and the parameters are measured at maximum memory frequency.
4.3.9.1
SDHC Electrical DC Characteristics
Table 43. SDHC Electrical DC Characteristics
ID Parameter Min Max Unit Comments
Table 43 lists the SDHC electrical DC characteristics.
General SD10 All Inputs SD11 Input Leakage Current -10 10 A -- Peak Voltage on All Lines -0.3 VDD + 0.3 V --
All Outputs SD12 Output Leakage Current -10 10 A --
Power Supply
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 80 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 43. SDHC Electrical DC Characteristics
ID SD13 SD14 SD15 SD16 Parameter Supply Voltage (low voltage) Supply Voltage (high voltage) Power Up Time Supply Current Min 1.65 2.7 -- 100 Max 1.95 3.6 250 -- Unit V V ms mA -- -- Comments 1.95 ~2.7 V is not supported.
Bus Signal Line Load SD17 SD18 Pull-up Resistance Open Drain Resistance 10 NA 100 NA k k Internal PU For MMC cards only -- VDD - 0.2 -- -- 0.3 V V IOH=-100 mA IOL= 2 mA
Open Drain Signal Level SD19 SD20 Output High Voltage Output Low Voltage
Push-Pull Signal Levels (High Voltage) SD21 SD22 SD23 SD24 Output HIGH Voltage Output LOW Voltage Input HIGH Voltage Input LOW Voltage 0.75 x VDD -- 0.625 x VDD VSS - 0.3 -- 0.125 x VDD VDD + 0.3 0.25 x VDD V V V V IOH=-100 mA @VDD min IOL=100 mA @VDD min -- --
Push-Pull Signal Levels (Low Voltage) SD25 SD26 SD27 SD28 Output HIGH Voltage Output LOW Voltage Input HIGH Voltage Input LOW Voltage VDD - 0.2 -- 0.7 x VDD VSS - 0.3 -- 0.2 VDD + 0.3 0.3 x VDD V V V V IOH=-100 mA @VDD min IOL=100 mA @VDD min -- --
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 81
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
4.3.10
Smart Liquid Crystal Display Controller (SLCDC)
Figure 43 and Figure 44 show the timings of the SLCDC, and Table 44 and Table 45 list the timing parameters.
tcss LCD_CS LCD_CLK (LCD_DATA[6]) tds SDATA (LCD_DATA[7]) MSB trss RS RS=0 => command data, RS=1=> display data This diagram illustrates the timing when the SCKPOL = 1, CSPOL = 0 tdh trsh LSB tcyc tcl tch tcsh
tcss LCD_CS LCD_CLK (LCD_DATA[6]) tds SDATA (LCD_DATA[7]) MSB trss RS tdh tcyc tcl tch
tcsh
trsh LSB
RS=0 => command data, RS=1=> display data This diagram illustrates the timing when the SCKPOL = 0, CSPOL = 0 tcss tcsh tcyc tcl tch tdh trsh LSB trss RS=0 => command data, RS=1=> display data This diagram illustrates the timing when the SCKPOL = 1, CSPOL = 1 tcss tcsh tcyc tcl tch
LCD_CS LCD_CLK (LCD_DATA[6])
tds SDATA (LCD_DATA[7]) MSB
RS
LCD_CS LCD_CLK (LCD_DATA[6])
tds SDATA (LCD_DATA[7]) MSB trss RS
tdh
trsh LSB
RS=0 => command data, RS=1=> display data This diagram illustrates the timing when the SCKPOL = 0, CSPOL = 1
Figure 43. SLCDC Timing Diagram--Serial Transfers to LCD Device
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 82 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 44. SLCDC Serial Interface Timing Parameters
Symbol tcss tcsh tcyc tcl tch tds tdh trss trsh Parameter Chip select setup time Chip select hold time Serial clock cycle time Serial clock low pulse Serial clock high pulse Data setup time Data hold time Register select setup time Register select hold time Min (tcyc / 2) () tprop (tcyc / 2) () tprop 39 () tprop 18 () tprop 18 () tprop (tcyc / 2) () tprop (tcyc / 2) () tprop (15 * tcyc / 2) () tprop (tcyc / 2) () tprop Typical -- -- -- -- -- -- -- -- -- Max -- -- 2641 -- -- -- -- -- -- Units ns ns ns ns ns ns ns ns ns
LCD_CLK trss LCD_RS tcyc LCD_CS tds LCD_DATA[15:0] tdh display data trsh
command data
This diagram illustrates the timing when CSPOL=0
LCD_CLK trss LCD_RS tcyc LCD_CS tds LCD_DATA[15:0] tdh display data trsh
command data
This diagram illustrates the timing when CSPOL=1
Figure 44. SLCDC Timing Diagram--Parallel Transfers to LCD Device Table 45. SLCDC Parallel Interface Timing Parameters
Symbol tcyc tds tdh Parameter Parallel clock cycle time Data setup time Data hold time Min 78 () tprop (tcyc / 2) () tprop (tcyc / 2) () tprop i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 83 Typical -- -- -- Max 4923 -- -- Units -- -- --
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 45. SLCDC Parallel Interface Timing Parameters (continued)
Symbol trss trsh Parameter Register select setup time Register select hold time Min (tcyc / 2) () tprop (tcyc / 2) () tprop Typical -- -- Max -- -- Units -- --
4.3.11
Synchronous Serial Interface (SSI)
This section describes the electrical information of SSI.
4.3.11.1
SSI Transmitter Timing with Internal Clock
Figure 45 and Figure 46 show the SSI transmitter timing with internal clock, and Table 46 lists the timing parameters.
SS1 SS2 AD1_TXC (Output) SS6 AD1_TXFS (bl) (Output) SS10 AD1_TXFS (wl) (Output) SS16 AD1_TXD (Output) SS43 SS42 AD1_RXD (Input) Note: SRXD Input in Synchronous mode only SS19 SS14 SS15 SS17 SS18 SS12 SS8 SS5 SS4 SS3
Figure 45. SSI Transmitter with Internal Clock Timing Diagram
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 84 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
SS1 SS2
SS5 SS4
SS3
DAM1_T_CLK (Output) SS6 DAM1_T_FS (bl) (Output) SS10 DAM1_T_FS (wl) (Output) SS16 DAM1_TXD (Output) SS43 SS42 DAM1_RXD (Input) Note: SRXD Input in Synchronous mode only SS19 SS14 SS15 SS17 SS18 SS12 SS8
Figure 46. SSI Transmitter with Internal Clock Timing Diagram Table 46. SSI Transmitter with Internal Clock Timing Parameters
ID Internal Clock Operation SS1 SS2 SS3 SS4 SS5 SS6 SS8 SS10 SS12 SS14 SS15 SS16 SS17 SS18 SS19 (Tx/Rx) CK clock period (Tx/Rx) CK clock high period (Tx/Rx) CK clock rise time (Tx/Rx) CK clock low period (Tx/Rx) CK clock fall time (Tx) CK high to FS (bl) high (Tx) CK high to FS (bl) low (Tx) CK high to FS (wl) high (Tx) CK high to FS (wl) low (Tx/Rx) Internal FS rise time (Tx/Rx) Internal FS fall time (Tx) CK high to STXD valid from high impedance (Tx) CK high to STXD high/low (Tx) CK high to STXD high impedance STXD rise/fall time 81.4 36.0 -- 36.0 -- -- -- -- -- -- -- -- -- -- -- -- -- 6 -- 6 15.0 15.0 15.0 15.0 6 6 15.0 15.0 15.0 6 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Parameter Min Max Unit
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 85
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 46. SSI Transmitter with Internal Clock Timing Parameters (continued)
ID Parameter Min Max Unit
Synchronous Internal Clock Operation SS42 SS43 SS52 SRXD setup before (Tx) CK falling SRXD hold after (Tx) CK falling Loading 10.0 0 -- -- -- 25 ns ns pF
*
* * *
All the timings for the SSI are given for a non-inverted serial clock polarity (TSCKP/RSCKP = 0) and a non-inverted frame sync (TFSI/RFSI = 0). If the polarity of the clock and/or the frame sync have been inverted, all the timing remains valid by inverting the clock signal STCK/SRCK and/or the frame sync STFS/SRFS shown in the tables and in the figures. All timings are on AUDMUX pads when SSI is being used for data transfer. "Tx" and "Rx" refer to the Transmit and Receive sections of the SSI. For internal Frame Sync operation using external clock, the FS timing will be same as that of Tx Data (for example, during AC97 mode of operation).
4.3.11.2
SSI Receiver Timing with Internal Clock
Figure 47 and Figure 48 show the SSI receiver timing with internal clock, and Table 47 lists the timing parameters.
SS1 SS2 AD1_TXC (Output) SS7 AD1_TXFS (bl) (Output) AD1_TXFS (wl) (Output) SS20 SS21 AD1_RXD (Input) SS47 SS48 AD1_RXC (Output) SS51 SS50 SS49 SS9 SS5 SS4 SS3
SS11
SS13
Figure 47. SSI Receiver with Internal Clock Timing Diagram
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 86 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
SS1 SS5 SS2 DAM1_T_CLK (Output) SS7 DAM1_T_FS (bl) (Output) DAM1_T_FS (wl) (Output) SS20 SS21 DAM1_RXD (Input) SS47 SS48 DAM1_R_CLK (Output) SS51 SS50 SS9 SS4
SS3
SS11
SS13
SS49
Figure 48. SSI Receiver with Internal Clock Timing Diagram Table 47. SSI Receiver with Internal Clock Timing Parameters
ID Parameter Internal Clock Operation SS1 SS2 SS3 SS4 SS5 SS7 SS9 SS11 SS13 SS20 SS21 (Tx/Rx) CK clock period (Tx/Rx) CK clock high period (Tx/Rx) CK clock rise time (Tx/Rx) CK clock low period (Tx/Rx) CK clock fall time (Rx) CK high to FS (bl) high (Rx) CK high to FS (bl) low (Rx) CK high to FS (wl) high (Rx) CK high to FS (wl) low SRXD setup time before (Rx) CK low SRXD hold time after (Rx) CK low 81.4 36.0 -- 36.0 -- -- -- -- -- 10.0 0 -- -- 6 -- 6 15.0 15.0 15.0 15.0 -- -- ns ns ns ns ns ns ns ns ns ns ns Min Max Unit
Oversampling Clock Operation SS47 SS48 Oversampling clock period Oversampling clock high period 15.04 6 -- -- ns ns
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 87
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 47. SSI Receiver with Internal Clock Timing Parameters (continued)
ID SS49 SS50 SS51 Parameter Oversampling clock rise time Oversampling clock low period Oversampling clock fall time Min -- 6 -- Max 3 -- 3 Unit ns ns ns
NOTE All the timings for the SSI are given for a non-inverted serial clock polarity (TSCKP/RSCKP = 0) and a non-inverted frame sync (TFSI/RFSI = 0). If the polarity of the clock and/or the frame sync have been inverted, all the timing remains valid by inverting the clock signal STCK/SRCK and/or the frame sync STFS/SRFS shown in the tables and in the figures. All timings are on AUDMUX pads when SSI is being used for data transfer. "Tx" and "Rx" refer to the Transmit and Receive sections of the SSI. For internal Frame Sync operation using external clock, the FS timing is the same as that of Tx Data, for example, during the AC97 mode of operation.
4.3.11.3
SSI Transmitter Timing with External Clock
Figure 49 and Figure 50 show the SSI transmitter timing with external clock, and Table 48 lists the timing parameters.
SS22 SS23 SS25 SS26
SS24
AD1_TXC (Input) AD1_TXFS (bl) (Input)
SS27
SS29
SS31 AD1_TXFS (wl) (Input) SS37 AD1_TXD (Output) SS45 SS44 AD1_RXD (Input) Note: SRXD Input in Synchronous mode only SS46 SS38
SS33
SS39
Figure 49. SSI Transmitter with External Clock Timing Diagram
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 88 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
SS22 SS23 DAM1_T_CLK (Input) SS27 DAM1_T_FS (bl) (Input) SS31 DAM1_T_FS (wl) (Input) SS37 DAM1_TXD (Output) SS29
SS26 SS25
SS24
SS33
SS39 SS38
SS44 DAM1_RXD (Input) Note: SRXD Input in Synchronous mode only
SS45
SS46
Figure 50. SSI Transmitter with External Clock Timing Diagram Table 48. SSI Transmitter with External Clock Timing Parameters
ID Parameter External Clock Operation SS22 SS23 SS24 SS25 SS26 SS27 SS29 SS31 SS33 SS37 SS38 SS39 (Tx/Rx) CK clock period (Tx/Rx) CK clock high period (Tx/Rx) CK clock rise time (Tx/Rx) CK clock low period (Tx/Rx) CK clock fall time (Tx) CK high to FS (bl) high (Tx) CK high to FS (bl) low (Tx) CK high to FS (wl) high (Tx) CK high to FS (wl) low (Tx) CK high to STXD valid from high impedance (Tx) CK high to STXD high/low (Tx) CK high to STXD high impedance 81.4 36.0 -- 36.0 -- -10.0 10.0 -10.0 10.0 -- -- -- -- -- 6.0 -- 6.0 15.0 -- 15.0 -- 15.0 15.0 15.0 ns ns ns ns ns ns ns ns ns ns ns ns Min Max Unit
Synchronous External Clock Operation SS44 SS45 SS46 SRXD setup before (Tx) CK falling SRXD hold after (Tx) CK falling SRXD rise/fall time 10.0 2.0 -- -- -- 6.0 ns ns ns
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 89
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
NOTE All the timings for the SSI are given for a non-inverted serial clock polarity (TSCKP/RSCKP = 0) and a non-inverted frame sync (TFSI/RFSI = 0). If the polarity of the clock and/or the frame sync have been inverted, all the timing remains valid by inverting the clock signal STCK/SRCK and/or the frame sync STFS/SRFS shown in the tables and in the figures. All timings are on AUDMUX pads when the SSI is being used for data transfer. "Tx" and "Rx" refer to the Transmit and Receive sections of the SSI. For internal Frame Sync operation using external clock, the FS timing will be same as that of Tx Data, for example, during the AC97 mode of operation.
4.3.11.4
SSI Receiver Timing with External Clock
Figure 51 and Figure 52 show the SSI receiver timing with external clock, and Table 49 lists the timing parameters.
SS22 SS26 SS23 AD1_TXC (Input) SS28 AD1_TXFS (bl) (Input) AD1_TXFS (wl) (Input) AD1_RXD (Input) SS30 SS25 SS24
SS32 SS35 SS41 SS40 SS36
SS34
Figure 51. SSI Receiver with External Clock Timing Diagram
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 90 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
SS22 SS26 SS23 SS25 SS24
DAM1_T_CLK (Input) SS28 DAM1_T_FS (bl) (Input) DAM1_T_FS (wl) (Input) DAM1_RXD (Input) SS30
SS32 SS35 SS41 SS40 SS36
SS34
Figure 52. SSI Receiver with External Clock Timing Diagram Table 49. SSI Receiver with External Clock Timing Parameters
ID Parameter External Clock Operation SS22 SS23 SS24 SS25 SS26 SS28 SS30 SS32 SS34 SS35 SS36 SS40 SS41 (Tx/Rx) CK clock period (Tx/Rx) CK clock high period (Tx/Rx) CK clock rise time (Tx/Rx) CK clock low period (Tx/Rx) CK clock fall time (Rx) CK high to FS (bl) high (Rx) CK high to FS (bl) low (Rx) CK high to FS (wl) high (Rx) CK high to FS (wl) low (Tx/Rx) External FS rise time (Tx/Rx) External FS fall time SRXD setup time before (Rx) CK low SRXD hold time after (Rx) CK low 81.4 36.0 -- 36.0 -- -10.0 10.0 -10.0 10.0 -- -- 10.0 2.0 -- -- 6.0 -- 6.0 15.0 -- 15.0 -- 6.0 6.0 -- -- ns ns ns ns ns ns ns ns ns ns ns ns ns Min Max Unit
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 91
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
NOTE All the timings for the SSI are given for a non-inverted serial clock polarity (TSCKP/RSCKP = 0) and a non-inverted frame sync (TFSI/RFSI = 0). If the polarity of the clock and/or the frame sync have been inverted, all the timing remains valid by inverting the clock signal STCK/SRCK and/or the frame sync STFS/SRFS shown in the tables and in the figures. All timings are on AUDMUX pads when the SSI is being used for data transfer. "Tx" and "Rx" refer to the Transmit and Receive sections of the SSI. For internal Frame Sync operation using external clock, the FS timing will be same as that of Tx Data, for example, during the AC97 mode of operation.
4.3.12
Wireless External Interface Module (WEIM)
All WEIM output control signals may be asserted and deasserted by internal clock related to BCLK rising edge or falling edge according to corresponding assertion/negation control fields. Address always begins related to BCLK falling edge but may be ended both on rising and falling edge in muxed mode according to control register configuration. Output data begins related to BCLK rising edge except in muxed mode where both rising and falling edge may be used according to control register configuration. Input data, ECB and DTACK all captured according to BCLK rising edge time. Figure 53 shows the timing of the WEIM module, and Table 50 lists the timing parameters.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 92 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
WEIM Outputs Timing WE22 WE21 BCLK (for rising edge timing) ... ... BCLK (for falling edge timing) Address CS[x] RW WE3 WE5 WE1
WE23
WE2 WE4 WE6
OE EB[x]
WE7
WE8
WE9
WE10
WE11 LBA WE13 Output Data WEIM Inputs Timing BCLK (for rising edge timing) WE16 Input Data WE15 WE18 ECB WE17 WE20 DTACK WE19
WE12 WE14
Figure 53. WEIM Bus Timing Diagram Table 50. WEIM Bus Timing Parameters
1.8 V ID Parameter Min WE1 WE2 WE3 WE4 Clock fall to address valid Clock rise/fall to address invalid Clock rise/fall to CS[x] valid Clock rise/fall to CS[x] invalid 0.68 0.68 0.45 0.45 Max 2.05 2.49 2.25 2.25 ns ns ns ns Unit
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 93
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 50. WEIM Bus Timing Parameters (continued)
1.8 V ID Parameter Min WE5 WE6 WE7 WE8 WE9 WE10 WE11 WE12 WE13 WE14 WE15 WE16 WE17 WE18 WE19 WE20 WE21 WE22 WE23 WE24 WE25 WE26 WE27 Note:
1
Unit Max 2.60 2.60 3.57 3.57 2.43 2.43 2.84 2.84 4.01 4.01 -- -- -- -- -- -- -- -- -- -- -- -- -- ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Clock rise/fall to RW Valid Clock rise/fall to RW Invalid Clock rise/fall to OE Valid Clock rise/fall to OE Invalid Clock rise/fall to EB[x] Valid Clock rise/fall to EB[x] Invalid Clock rise/fall to LBA Valid Clock rise/fall to LBA Invalid Clock rise/fall to Output Data Valid Clock rise to Output Data Invalid Input Data Valid to Clock rise, FCE=0 Cloc/k rise to Input Data Invalid, FCE=0 Input Data Valid to Clock rise, FCE=1 Clock rise to Input Data Invalid, FCE=1 ECB setup time, FCE=0 ECB hold time, FCE=0 ECB setup time, FCE=1 ECB hold time, FCE=1 DTACK setup time DTACK hold time BCLK High Level Width1 BCLK Low Level Width1
0.90 0.90 1.17 1.17 0.73 0.73 1.03 1.03 1.04 1.04 6.95 2.35 1.24 0.23 7.23 2.93 1.08 0 5.35 3.19 3.0 3.0 7.5
BCLK Cycle time1
BCLK parameters are being measured from the 50% point--that is, high is defined as 50% of signal value and low is defined as 50% of signal value.
NOTE High is defined as 80% of signal value and low is defined as 20% of signal value. Test conditions: pad voltage, 1.7-1.95 V; pad capacitance, 25 pF. Recommended drive strength for all controls, address, and BCLK is Max High.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 94 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Figure 54, Figure 55, Figure 34, Figure 57, Figure 58, and Figure 59 show examples of basic WEIM accesses to external memory devices with the timing parameters mentioned in Table 50 for specific control parameter settings.
BCLK WE1 ADDR CS[x] RW WE11 LBA WE7 WE12 Last Valid Address WE3 V1 WE2 Next Address WE4
OE
WE8
WE9 EB[y]
WE10
WE16 DATA V1 WE15
Figure 54. Asynchronous Memory Timing Diagram for Read Access--WSC=1
BCLK WE1 ADDR CS[x] Last Valid Address WE3 WE5 RW LBA OE WE9 EB[y] WE10 WE14 DATA WE13 V1 WE11 WE12 V1 WE4 WE6 WE2 Next Address
Figure 55. Asynchronous Memory Timing Diagram for Write Access--WSC=1, EBWA=1, EBWN=1, LBN=1
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 95
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
BCLK WE1 ADDR Last Valid Addr CS[x] RW WE11 WE12 WE8 WE3 Address V1 WE2 Address V2 WE4
LBA
OE EB[y]
WE7
WE9 WE18 WE18
WE10
ECB WE17 WE16 DATA WE15
V1 V1+2 Halfword Halfword
WE17 WE16
V2 Halfword V2+2 Halfword
WE15
Figure 56. Synchronous Memory Timing Diagram for Two Non-Sequential Read Accesses: WSC=2, SYNC=1, DOL=0
BCLK WE1 ADDR Last Valid Addr CS[x] WE3 Address V1 WE4 WE2
RW
WE5 WE11 WE12
WE6
LBA
OE EB[y] WE9 WE10
WE18 ECB WE17 WE14 DATA WE13 V1 WE13 WE14 V1+4 V1+8 V1+12
Figure 57. Synchronous Memory TIming Diagram for Burst Write Access--BCS=1, WSC=4, SYNC=1, DOL=0, PSR=1
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 96 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
BCLK WE1 ADDR/ M_DATA Last Valid Addr CS[x] WE3
WE2 Address V1 WE13 Write Data
WE14 WE4
RW
WE5 Write WE11 WE12
WE6
LBA
OE EB[y] WE9 WE10
Figure 58. Muxed A/D Mode Timing Diagram for Asynchronous Write Access--WSC=7, LBA=1, LBN=1, LAH=1
BCLK WE1 ADDR/ Last Valid Addr M_DATA WE3 CS[x] WE2 Address V1 WE16 Read Data WE15 WE4 RW WE11 LBA WE12
OE WE9
WE7
WE8
EB[y]
WE10
Figure 59. Muxed A/D Mode Timing Diagram for Asynchronous Read Access--WSC=7, LBA=1, LBN=1, LAH=1, OEA=7
4.3.13
USBOTG Electricals
This section describes the electrical information of the USB OTG port and host ports.
4.3.14
Serial Interface
In order to support four serial different interfaces, the USBOTG transceiver can be configured to operate in one of the following modes: * DAT_SE0 bidirectional, 3-wire mode * DAT_SE0 unidirectional, 6-wire mode
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 97
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
* *
VP_VM bidirectional, 4-wire mode VP_VM unidirectional, 6-wire mode
4.3.14.1
DAT_SE0 Bidirectional Mode
Table 51. Signal Definitions--DAT_SE0 Bidirectional Mode
Name USB_TXOE_B USB_DAT_VP USB_SE0_VM Direction Out Out In Out In Signal Description * Transmit enable, active low * TX data when USB_TXOE_B is low * Differential RX data when USB_TXOE_B is high * SE0 drive when USB_TXOE_B is low * SE0 RX indicator when USB_TXOE_B is high
USB_DAT_VP USB_SE0_VM
Figure 60. USB Transmit Waveform in DAT_SE0 Bidirectional Mode
USB_TXOE_B USB_DAT_VP USB_SE0_VM
Figure 61. USB Receive Waveform in DAT_SE0 Bidirectional Mode
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 98 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 52. OTG Port Timing Specification in DAT_SE0 Bidirectional Mode
Parameter TX Rise/Fall Time TX Rise/Fall Time TX Rise/Fall Time TX Duty Cycle Enable Delay Disable Delay RX Rise/Fall Time RX Rise/Fall Time Signal Name USB_DAT_VP USB_SE0_VM USB_TXOE_B USB_DAT_VP USB_DAT_VP USB_SE0_VM USB_DAT_VP USB_SE0_VM USB_DAT_VP USB_SE0_VM Direction Out Out Out Out In In In In Min -- -- -- 49.0 -- -- -- -- Max 5.0 5.0 5.0 51.0 8.0 10.0 3.0 3.0 Unit ns ns ns % ns ns ns ns Conditions/ Reference Signal 50 pF 50 pF 50 pF -- USB_TXOE_B USB_TXOE_B 35 pF 35 pF
4.3.14.2
DAT_SE0 Unidirectional Mode
Table 53. Signal Definitions--DAT_SE0 Unidirectional Mode
Name USB_TXOE_B USB_DAT_VP USB_SE0_VM USB_VP1 USB_VM1 USB_RCV Direction Out Out Out In In In Signal Description Transmit enable, active low TX data when USB_TXOE_B is low. SE0 drive when USB_TXOE_B is low. Buffered data on DP when USB_TXOE_B is high. Buffered data on DM when USB_TXOE_B is high. Differential RX data when USB_TXOE_B is high.
USB_DAT_VP USB_SE0_VM
Figure 62. USB Transmit Waveform in DAT_SE0 Unidirectional Mode
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 99
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
USB_DAT_VP/ USB_SE0_VM VP, VM, RCV
Figure 63. USB Receive Waveform in DAT_SE0 Unidirectional Mode Table 54. OTG Port Timing Specification in DAT_SE0 Unidirectional Mode
Parameter TX Rise/Fall Time TX Rise/Fall Time TX Rise/Fall Time TX Duty Cycle Enable Delay Disable Delay RX Rise/Fall Time RX Rise/Fall Time RX Rise/Fall Time Signal Name USB_DAT_VP USB_SE0_VM USB_TXOE_B USB_DAT_VP USB_DAT_VP USB_SE0_VM USB_DAT_VP USB_SE0_VM USB_VP1 USB_VM1 USB_RCV Signal Source Out Out Out Out In In In In In Min -- -- -- 49.0 -- -- -- -- -- Max 5.0 5.0 5.0 51.0 8.0 10.0 3.0 3.0 3.0 Unit ns ns ns % ns ns ns ns ns Condition/ Reference Signal 50 pF 50 pF 50 pF -- USB_TXOE_B USB_TXOE_B 35 pF 35 pF 35 pF
4.3.14.3
VP_VM Bidirectional Mode
Table 55. Signal Definitions--VP_VM Bidirectional Mode
Name USB_TXOE_B USB_DAT_VP USB_SE0_VM USB_RCV Direction Out Out (Tx) In (Rx) Out (Tx) In (Rx) In Signal Description * Transmit enable, active low * TX VP data when USB_TXOE_B is low * RX VP data when USB_TXOE_B is high * TX VM data when USB_TXOE_B low * RX VM data when USB_TXOE_B high * Differential RX data
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 100 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Freescale Semiconductor USB_SE0_VM
Figure 64. USB Transmit Waveform in VP_VM Bidirectional Mode
Figure 65. USB Receive Waveform in VP_VM Bidirectional Mode
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 USB_TXOE_B USB_DAT_VP USB_SE0_VM USB_SE0_VM
USB_TXOE_B USB_DAT_VP USB_SE0_VM
Electrical Characteristics
101
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 56. OTG Port Timing Specification in VP_VM Bidirectional Mode
Parameter TX Rise/Fall Time TX Rise/Fall Time TX Rise/Fall Time TX Duty Cycle TX High Overlap TX Low Overlap Enable Delay Disable Delay RX Rise/Fall Time RX Rise/Fall Time RX Skew RX Skew Signal Name USB_DAT_VP USB_SE0_VM USB_TXOE_B USB_DAT_VP USB_SE0_VM USB_SE0_VM USB_DAT_VP USB_SE0_VM USB_DAT_VP USB_SE0_VM USB_DAT_VP USB_SE0_VM USB_DAT_VP USB_RCV Direction Out Out Out Out Out Out In In In In Out Out Min -- -- -- 49.0 0.0 -- -- -- -- -- -4.0 -6.0 Max 5.0 5.0 5.0 51.0 -- 0.0 8.0 10.0 3.0 3.0 +4.0 +2.0 Unit ns ns ns % ns ns ns ns ns ns ns ns Condition/ Reference Signal 50 pF 50 pF 50 pF -- USB_DAT_VP USB_DAT_VP USB_TXOE_B USB_TXOE_B 35 pF 35 pF USB_SE0_VM USB_DAT_VP
4.3.14.4
VP_VM Unidirectional Mode
Table 57. Signal Definitions--VP_VM Unidirectional Mode
Name USB_TXOE_B USB_DAT_VP USB_SE0_VM USB_VP1 USB_VM1 USB_RCV Direction Out Out Out In In In Signal Description Transmit enable, active low TX VP data when USB_TXOE_B is low TX VM data when USB_TXOE_B is low RX VP data when USB_TXOE_B is high RX VM data when USB_TXOE_B is high Differential RX data
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 102 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Freescale Semiconductor USB_SE0_VM
Figure 66. USB Transmit Waveform in VP_VM Unidirectional Mode
Figure 67. USB Receive Waveform in VP_VM Unidirectional Mode
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 USB_VP1 USB_VM1 USB_TXOE_B UH1_RXD
USB_TXOE_B USB_DAT_VP USB_SE0_VM
Electrical Characteristics
103
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Electrical Characteristics
Table 58. USB Timing Specification in VP_VM Unidirectional Mode
Parameter TX Rise/Fall Time TX Rise/Fall Time TX Rise/Fall Time TX Duty Cycle TX High Overlap TX Low Overlap Enable Delay Disable Delay RX Rise/Fall Time RX Rise/Fall Time RX Skew RX Skew Signal USB_DAT_VP USB_SE0_VM USB_TXOE_B USB_DAT_VP USB_SE0_VM USB_SE0_VM USB_DAT_VP USB_SE0_VM USB_DAT_VP USB_SE0_VM USB_VP1 USB_VM1 USB_VP1 USB_RCV Direction Out Out Out Out Out Out In In In In Out Out Min -- -- -- 49.0 0.0 -- -- -- -- -- -4.0 -6.0 Max 5.0 5.0 5.0 51.0 -- 0.0 8.0 10.0 3.0 3.0 +4.0 +2.0 Unit ns ns ns % ns ns ns ns ns ns ns ns Conditions/ Reference Signal 50 pF 50 pF 50 pF -- USB_DAT_VP USB_DAT_VP USB_TXOE_B USB_TXOE_B 35 pF 35 pF USB_SE0_VM USB_DAT_VP
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 104 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
5
Package Information and Pinout
The i.MX27/MX27L processor is available in a 17 mm x 17 mm, 0.65 mm pitch, 404-pin MAPBGA package and a 19 mm x 19 mm, 0.8 mm pitch, 473-pin MAPBGA package.
5.1
Full Package Outline Drawing (17 mm x 17 mm)
Figure 68 shows the package drawings and dimensions of the production package.
Figure 68. i.MX27/MX27L 17 mm x 17 mm Full Package MAPBGA: Mechanical Drawing
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 105
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
5.2
Pin Assignments (17 mm x 17 mm)
Table 59 on page 107 shows the i.MX27 full 17 x 17 mm package MAPBGA pin assignments. Table 60 on page 112 identifies the pin assignments for the ball grid array (BGA) for full package. The list is sorted alphabetically by the name of the contact. The connections of these pins depend solely upon the user application, however there are a few factory test signals that are not used in a normal application. Following is a list of these signals and how they are to be terminated for proper operation of the i.MX27/MX27L processor: * CLKMODE[1:0]: To ensure proper operation, leave these signals as no connects. * OSC26M_TEST: To ensure proper operation, leave this signal as no connect. * EXT_60M: To ensure proper operation, connect this signal to ground. * EXT_266M: To ensure proper operation, connect this signal to ground. * Most of the signals shown in Table 59 are multiplexed with other signals. For ease of reference, all of the signals at a particular pad are shown in the form of a compound signal name. Please refer to Table 3 for complete information on the signal multiplexing schemes of these signals.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 106 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
24 24
GND GND CSPI2_SS1_USBH2 _DATA3_PD2 CSPI2_SCLK_USBH2 _DATA0_PD22 CSPI2_SS2_USBH2 _DATA4_PD19 CSPI1_SS2_USBH2 _DATA5 CSPI2_MOSI_ USBH2_DATA1 USBH1_OE_B_PB27 USBH1_TXDP_UART4 _CTS_PB29 USBH1_RXDP_ UART4_RXD
23
22
SD1_CMD_CSPI3 _MOSI_PE22 CSPI1_RDY _PD25 SD1_D0_CSPI3 _MISO_PE18 RTCK_OWIRE _PE16
21
20
19
18
Table 59. i.MX27 Full 17 x 17 mm Package MAPBGA Pin Assignment
UART3_CTS_ PE10 UART1_TXD _PE12 UART3_TXD _PE8 UART2_TXD_KP _COL6_PE6
17
16
15
UART2_RTS_KP _ROW7_PE4 KP_COL0 KP_ROW5 I2C_CLK_PD18 PWMO_PE5 KP_COL3
UART2_RXD_KP _ROW6_PE7
14
13
12
SSI3_RXDAT_SLCDC2 SSI3_CLK_ _RS_PC29 SLCDC2CLK_PC31 SSI2_RXDAT_GPT5 _TIN_PC25 SSI2_CLK_GPT4 _TIN_PC27 SSI1_CLK_PC23 SSI3_TXDAT_ SLCDC2_CS_PC30 SD2_D2_MSHC _DATA2_PB6 SSI1_RXDAT _PC21 SSI4_RXDAT _PC17 SSI4_CLK _PC19 TIN_PC15 CSI_HSYNC_ UART5_RTS_PB21 CSI_D5_PB17 CSI_D7_UART5 _RXD_PB19 CSI_MCLK_PB15 SD2_CMD_MSHC _BS_PB8 CSI_D0_UART6 _TXD_PB10 CSI_D1_UART6 _RXD_PB11 SPL_SPR_PA27 OE_ACD_PA31
11
SSI3_FS_SLCDC2 _D0_PC28 SSI1_TXDAT_PC22
10
9
TOUT_PC14
8
CSI_PIXCLK_PB16
7
CSI_D2_UART6 _CTS_PB12
6
CSI_D3_UART6_ RTS_PB13 SD2_CLK_MSHC _SCLK_PB9 SD2_D3_MSHC _DATA3_PB7 GND GND
5
4
SD2_D1_MSHC _DATA1_PB5 GND GND CONTRAST _PA30 SD2_D0_MSHC _DATA0_PB4 C PS_PA26 HSYNC_PA28 LD16_PA22 REV_PA24
3
2
1
D
A
B
i.MX27/i.MX27L Block Guide, Rev. 1.5 Freescale Semiconductor 107
E
1
2
3
4
5
6
7
8
9
10
11
KP_ROW4
12
KP_ROW1 KP_ROW3 KP_ROW2
UART2_CTS_KP _COL7_PE3
13
14
15
KP_COL2 KP_COL4
UART3_RTS_PE11
16
UART1_RTS_PE15
TDO
17
TRST_B
SD1_D1_PE19
18
UART1_CTS_PE14 TDI
SD1_D3_CSPI3 _SS_PE21
19
TMS
USBH1_FS_UART4 _RTS_PB26
20
SD1_D2_PE20
CSPI1_SS1_PD27
21
CSPI1_MOSI_PD31
22
CSPI1_MISO_PD30 CSPI1_SS0 _PD28
23
GND GND
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
24 24
I2C2_SCL_PC6 USBOTG_DATA6 _PC8 USBOTG_DATA4 _PC12 USBOTG_CLK _PE24 USBOTG_DATA2 _PC10 USBH2_DATA7 _PA2
23
22
21
CSPI2_SS0_USBH2 _DATA6_PD21 USBH1_TXDM_UART4 _TXD_PB28 CSPI1_SCLK_PD29 USBOTG_DATA1 _PC11 SD1_CLK_CSPI3 _SCLK_PE23 NVDD14 UPLLVDD RTCVSS
CSPI2_MISO_USBH2 _DATA2_PD23
20
19
Table 59. i.MX27 Full 17 x 17 mm Package MAPBGA Pin Assignment (continued)
18
17
16
15
14
13
12
11
SSI2_TXDAT_GPT4 _TOUT_PC26 NVDD11 SSI1_FS_PC20 SSI2_FS_GPT5 _TOUT_PC24 SSI4_TXDAT_PC18
10
9
SSI4_FS_PC16
8
CSI_D6_UART5 _TXD_PB18 CSI_VSYNC_UART5 _CTS_PB20 CLS_PA25 CSI_D4_PB14
NVDD15
LD11_PA17
LD9_PA15
7
LD15_PA21
LD5_PA11
LD1_PA7
6
VSYNC_PA29
LD17_PA23
LD13_PA19
LD7_PA13
LD3_PA9
5
4
3
2
1
G
H
i.MX27/i.MX27L Block Guide, Rev. 1.5 108 Freescale Semiconductor
K
F
J
1
LD14_PA20
LD8_PA14
NFRB_ETMTRACEPKT3_PF0
NFWP_B_ NFALE_ETMPIPE ETMTRACEPKT1_PF2 STAT0_PF4
2
LD10_PA16
LD6_PA12
LD4_PA10
LD0_PA6
LSCLK_PA5
3
LD12_PA18
LD2_PA8
4
5
6
7
8
9
10
GND
11
KP_ROW0 NVDD10
GND
12
I2C_DATA_PD17 QVDD
GND
13
KP_COL1 QVDD
GND
14
KP_COL5 NVDD9
GND
15
UART3_RXD_PE9 NVDD8
GND
16
UART1_RXD_PE13
17
TCK
18
19
USBH1_SUSP_PB22
USBOTG_DATA5 _PC7
USBOTG_DATA0 _PC9 RTCVDD
20
USB_OC_B_PB24
USBH1_RXDM _PB30 USBOTG_DATA3 _PC13
21
22
USBH1_RCV_PB25
I2C2_SDA_PC5
23
USB_PWR_PB23
USBH2_CLK_PA0
USBH2_STP_PA4 USBH2_DIR_PA1
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
24 24
OSC32K_BYPASS EXTAL32K XTAL32K ATA_DATA1_SD3_ D1_PD3 ATA_DATA0_SD3_ D0_PD2 SD3_CLK_ETMTRACE PKT15_PD1
USBOTG_STP_KP _ROW6A_PE1
23
22
21
20
19
Table 59. i.MX27 Full 17 x 17 mm Package MAPBGA Pin Assignment (continued)
18
17
16
15
14
13
12
11
10
9
8
NVDD12 NVDD1
NVDD1
QVDD
NVDD2
7
NFCLE_ETMTRAC EPKT0_PF1 D9 NFRE_B_ETMPIP ESTAT1_PF5 D13
D1
A12
A7
6
D3
A9
A5
5
4
3
NFCE_B_ETMTRACE PKT2_PF3 NFWE_B_ETMPIPE STAT2_PF6 L
2
1
M
N
i.MX27/i.MX27L Block Guide, Rev. 1.5 109 Freescale Semiconductor
R
P
1
D14
D12
D10
D6
2
D15
D7
D8
D4
3
D11
D5
4
5
6
7
8
9
10
GND GND
GND
GND
GND
11
GND GND GND
GND
GND
12
GND GND GND
GND
GND
13
GND GND GND
GND
GND
14
GND GND GND GND
GND
15
GND UPLLVSS MPLLVSS FPMVSS
GND
16
17
18
NVDD7 FPMVDD FUSEVDD NVDD6
NVDD6
19
NVDD7 FUSEVSS
NVDD13 POWER_ON_RESET
ATA_DATA6_FEC _MDIO_PD8
20
USBH2_NXT_PA3 USBOTG_NXT_KP _COL6A_PE0 ATA_DATA10_ ETMTRACEPKT9_PD12 ATA_DATA2_SD3 _D2_PD4
USBOTG_DIR_KP _ROW7A_PE2
21
22
USBOTG_DATA7_PE25 POWER_CUT
23
OSC32VDD OSC32VSS
SD3_CMD_PD0
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
ATA_DATA3_SD3_ D3_PD5 ATA_DATA5_ETMTRACE PKT13_PD7 ATA_DATA4_ETMTRACE PKT14_PD6 ATA_DATA8_ETMTRACE PKT11_PD10 ATA_DATA12_ETMTRACE PKT7_PD14 ATA_DATA7_ETMTRACE PKT12_PD9 ATA_DATA13_ ATA_DATA9_ ATA_DATA15_ETM ETMTRACEPKT10_PD11 ETMTRACEPKT6_PD15 TRACEPKT4_PF23
23
22
21
ATA_DATA14_ETMTRACE PKT5_PD16
IOIS16_ATA_ INTRQ_PF9 PC_POE_ATA _BUFFER_EN_PF7
PC_BVD2_ATA _DMACK_PF11 PC_VS2_ATA _DA0_PF13 PC_PWRON_ATA _DA2_PF16 PC_WAIT_B_ATA _CS1_PF18 OE_B PC_CD1_B_ATA _DIOR_PF20 EXT_60M
20
19
Table 59. i.MX27 Full 17 x 17 mm Package MAPBGA Pin Assignment (continued)
18
17
16
15
14
13
12
11
10
NVDD2
SD13
SD12
9
A19
SDQS1
SD15
8
NVDD2
NVDD2
SD29
SD25
SD18
7
A1
A25
SD28
SDQS2
A20
6
SDBA1
SD31
SD26
SD23
5
4
3
2
1
W
U
V
i.MX27/i.MX27L Block Guide, Rev. 1.5 110 Freescale Semiconductor
Y
T
1
D2
A13
A8
A4
A0
2
D0
A11
A6
A2
SDBA0
3
MA10
A3
SDQS3
4
5
6
7
8
9
10
NVDD2
SD6
SD8
11
NVDD3
A16
A15
12
NVDD3 DQM1
SD2
13
NVDD4 SDWE_B
DQM2
14
QVDD CS3_B
SDCKE1
15
QVDD CS5_B_ETMTRACE CLK_PF22
CS2_B
16
QVDD
EB0_B LBA_B
17
NVDD5
18
MPLLVDD
AVDD NVDD5
19
AVSS
BOOT2 OSC26M_TEST
20
21
22
BOOT3
23
BOOT0
ATA_DATA11_ ETMTRACEPKT8_PD13 BOOT1
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
24 24
Package Information and Pinout
24 24
XTAL26M EXTAL26M GND GND
23
RESET_OUT _B_PE17
22
21
20
Table 59. i.MX27 Full 17 x 17 mm Package MAPBGA Pin Assignment (continued)
PC_CD2_B_ATA _DIOW_PF19 PC_READY_ATA _CS0_PF17 EXT_266M JTAG_CTRL
19
18
17
16
15
14
13
12
11
10
A14
SD5 SDQS0
9
SD10
SD9 SD7
8
A17
SD11
7
A18
SD14
6
SD21
SD17
SD16
5
A21
SD20
SD19
4
3
2
1
i.MX27/i.MX27L Block Guide, Rev. 1.5 Freescale Semiconductor 111
AD
AA
AB
AC
1
SD30
A23
GND
GND
2
A24
SD24
GND
GND
3
SD27
A22
SD22
4
5
6
7
8
9
10
SD4 SD3
11
SD1 DQM3
12
SD0
A10 DQM0
13
RAS_B
CAS_B SDCLK
14
SDCKE0 SDCLK_B
15
RW_B CS4_B_ETMTRACE SYNC_PF21
16
CS1_B
ECB_B CS0_B
17
BCLK
EB1_B CLKO_PF15
18
19
20
CLKMODE0
PC_VS1_ATA _DA1_PF14 PC_BVD1_ATA _DMARQ_PF12
21
CLKMODE1
PC_RST_ATA_ RESET_B_PF10 PC_RW_B_ATA _IORDY_PF8
22
RESET_IN_B POR_B
23
OSC26VDD
OSC26VSS
GND GND
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 60 shows the device pin list, sorted by signal identification, including pad locations for ground and power supply voltages.
Table 60. i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing
Contact Name A0 A1 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A2 A20 A21 A22 A23 A24 A25 A3 A4 A5 A6 A7 A8 A9 ATA_DATA0_SD3_D0_PD2 ATA_DATA1_SD3_D1_PD3 ATA_DATA10_ETMTRACEPKT9_PD12 ATA_DATA11_ETMTRACEPKT8_PD13 ATA_DATA12_ETMTRACEPKT7_PD14 Location Y1 T6 AC12 U2 P6 U1 AB9 Y11 W11 AC7 AC6 V8 W2 Y6 AB4 AC3 AB1 AA2 U6 U3 W1 R5 V2 R6 V1 P5 R23 R24 R20 W23 U23
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 112 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 60. i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing (continued)
Contact Name ATA_DATA13_ETMTRACEPKT6_PD15 ATA_DATA14_ETMTRACEPKT5_PD16 ATA_DATA15_ETMTRACEPKT4_PF23 ATA_DATA2_SD3_D2_PD4 ATA_DATA3_SD3_D3_PD5 ATA_DATA4_ETMTRACEPKT14_PD6 ATA_DATA5_ETMTRACEPKT13_PD7 ATA_DATA6_FEC_MDIO_PD8 ATA_DATA7_ETMTRACEPKT12_PD9 ATA_DATA8_ETMTRACEPKT11_PD10 ATA_DATA9_ETMTRACEPKT10_PD11 AVDD AVSS BCLK BOOT0 BOOT1 BOOT2 BOOT3 CAS_B CLKMODE0 CLKMODE1 CLKO_PF15 CLS_PA25 CONTRAST_PA30 CS0_B CS1_B CS2_B CS3_B CS4_B_ETMTRACESYNC_PF21 CS5_B_ETMTRACECLK_PF22 CSI_D0_UART6_TXD_PB10 CSI_D1_UART6_RXD_PB11 CSI_D2_UART6_CTS_PB12 Location W24 T20 Y24 P20 T24 T22 T23 P19 U24 U22 V24 U18 T19 AB17 V23 Y23 U19 Y22 AC13 AB20 AB21 AD17 G6 C2 AD16 AB16 Y15 W14 AD15 W15 C4 B4 E6
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 113
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 60. i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing (continued)
Contact Name CSI_D3_UART6_RTS_PB13 CSI_D4_PB14 CSI_D5_PB17 CSI_D6_UART5_TXD_PB18 CSI_D7_UART5_RXD_PB19 CSI_HSYNC_UART5_RTS_PB21 CSI_MCLK_PB15 CSI_PIXCLK_PB16 CSI_VSYNC_UART5_CTS_PB20 CSPI1_MISO_PD30 CSPI1_MOSI_PD31 CSPI1_RDY_PD25 CSPI1_SCLK_PD29 CSPI1_SS0_PD28 CSPI1_SS1_PD27 CSPI1_SS2_USBH2_DATA5_PD26 CSPI2_MISO_USBH2_DATA2_PD23 CSPI2_MOSI_USBH2_DATA1_PD24 CSPI2_SCLK_USBH2_DATA0_PD22 CSPI2_SS0_USBH2_DATA6_PD21 CSPI2_SS1_USBH2_DATA3_PD20 CSPI2_SS2_USBH2_DATA4_PD19 D0 D1 D10 D11 D12 D13 D14 D15 D2 D3 D4 Location A5 F6 A6 F7 B6 A7 B5 E7 G7 A22 C21 B21 F18 B22 C20 E22 G20 E23 D23 F20 C23 D22 T2 N6 P1 M3 N1 M5 M1 M2 T1 N5 R2
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 114 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 60. i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing (continued)
Contact Name D5 D6 D7 D8 D9 DQM0 DQM1 DQM2 DQM3 EB0_B EB1_B ECB_B EXT_266M EXT_60M EXTAL26M EXTAL32K FPMVDD FPMVSS FUSEVDD FUSEVSS GND GND GND GND GND GND GND GND GND GND GND GND GND Location N3 R1 N2 P2 M6 AD12 W12 Y13 AD11 W16 AC17 AC16 AD18 W17 AB24 M24 M18 P15 R18 R19 A1 A2 A23 A24 AC1 AC2 AC23 AC24 AD1 AD2 AD23 AD24 B1
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 115
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 60. i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing (continued)
Contact Name GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Location B2 B23 B24 K10 K11 K12 K13 K14 K15 L10 L11 L12 L13 L14 L15 M10 M11 M12 M13 M14 N10 N11 N12 N13 N14 N15 P10 P11 P12 P13 P14 R10 R11
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 116 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 60. i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing (continued)
Contact Name GND GND GND HSYNC_PA28 I2C_CLK_PD18 I2C_DATA_PD17 I2C2_SCL_PC6 I2C2_SDA_PC5 IOIS16_ATA_INTRQ_PF9 JTAG_CTRL KP_COL0 KP_COL1 KP_COL2 KP_COL3 KP_COL4 KP_COL5 KP_ROW0 KP_ROW1 KP_ROW2 KP_ROW3 KP_ROW4 KP_ROW5 LBA_B LD0_PA6 LD1_PA7 LD10_PA16 LD11_PA17 LD12_PA18 LD13_PA19 LD14_PA20 LD15_PA21 LD16_PA22 LD17_PA23 Location R12 R13 R14 D1 B13 F12 F24 J22 U20 AC18 B14 F13 A15 E13 B15 F14 F11 A12 C12 B12 E11 A13 Y16 J2 K6 F2 J7 H3 H5 F1 H6 E2 G5
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 117
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 60. i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing (continued)
Contact Name LD2_PA8 LD3_PA9 LD4_PA10 LD5_PA11 LD6_PA12 LD7_PA13 LD8_PA14 LD9_PA15 LSCLK_PA5 MA10 MPLLVDD MPLLVSS NFALE_ETMPIPESTAT0_PF4 NFCE_B_ETMTRACEPKT2_PF3 NFCLE_ETMTRACEPKT0_PF1 NFRB_ETMTRACEPKT3_PF0 NFRE_B_ETMPIPESTAT1_PF5 NFWE_B_ETMPIPESTAT2_PF6 NFWP_B_ETMTRACEPKT1_PF2 NVDD1 NVDD1 NVDD10 NVDD11 NVDD12 NVDD13 NVDD14 NVDD15 NVDD2 NVDD2 NVDD2 NVDD2 NVDD2 NVDD3 Location J3 K5 H2 J6 G2 J5 G1 K7 K2 T3 T18 R15 K1 L2 L6 H1 L5 L1 J1 M7 N7 G11 G10 L7 M19 H18 H7 R7 T7 U7 V10 V9 V11
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 118 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 60. i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing (continued)
Contact Name NVDD3 NVDD4 NVDD5 NVDD5 NVDD6 NVDD6 NVDD7 NVDD7 NVDD8 NVDD9 OE_ACD_PA31 OE_B OSC26M_TEST OSC26VDD OSC26VSS OSC32K_BYPASS OSC32VDD OSC32VSS PC_BVD1_ATA_DMARQ_PF12 PC_BVD2_ATA_DMACK_PF11 PC_CD1_B_ATA_DIOR_PF20 PC_CD2_B_ATA_DIOW_PF19 PC_POE_ATA_BUFFER_EN_PF7 PC_PWRON_ATA_DA2_PF16 PC_READY_ATA_CS0_PF17 PC_RST_ATA_RESET_B_PF10 PC_RW_B_ATA_IORDY_PF8 PC_VS1_ATA_DA1_PF14 PC_VS2_ATA_DA0_PF13 PC_WAIT_B_ATA_CS1_PF18 POR_B POWER_CUT POWER_ON_RESET Location V12 V13 V17 V18 N18 P18 L18 L19 G15 G14 D3 Y17 V19 AA23 AB23 L24 M23 N23 AD20 W20 W18 AC19 V20 Y19 AD19 AC21 AD21 AC20 W19 Y18 AD22 N22 N19
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 119
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 60. i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing (continued)
Contact Name PS_PA26 PWMO_PE5 QVDD QVDD QVDD QVDD QVDD QVDD QVDD RAS_B RESET_IN_B RESET_OUT_B_PE17 REV_PA24 RTCK_OWIRE_PE16 RTCVDD RTCVSS RW_B SD0 SD1 SD1_CLK_CSPI3_SCLK_PE23 SD1_CMD_CSPI3_MOSI_PE22 SD1_D0_CSPI3_MISO_PE18 SD1_D1_PE19 SD1_D2_PE20 SD1_D3_CSPI3_SS_PE21 SD10 SD11 SD12 SD13 SD14 SD15 SD16 SD17 Location D2 C13 G12 G13 G16 P7 V14 V15 V16 AB13 AC22 AA22 E1 A19 K19 K18 AC15 AB12 AC11 G17 A21 A20 E17 B20 E18 AB8 AD7 Y9 W9 AD6 Y8 AD5 AC5
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 120 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 60. i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing (continued)
Contact Name SD18 SD19 SD2 SD2_CLK_MSHC_SCLK_PB9 SD2_CMD_MSHC_BS_PB8 SD2_D0_MSHC_DATA0_PB4 SD2_D1_MSHC_DATA1_PB5 SD2_D2_MSHC_DATA2_PB6 SD2_D3_MSHC_DATA3_PB7 SD20 SD21 SD22 SD23 SD24 SD25 SD26 SD27 SD28 SD29 SD3 SD3_CLK_ETMTRACEPKT15_PD1 SD3_CMD_PD0 SD30 SD31 SD4 SD5 SD6 SD7 SD8 SD9 SDBA0 SDBA1 SDCKE0 Location Y7 AD4 Y12 A4 C5 C1 E3 C8 A3 AC4 AB5 AD3 W5 AB2 W7 V5 AA3 V6 V7 AD10 P24 P23 AA1 U5 AC10 AC9 W10 AD8 Y10 AC8 Y2 T5 AC14
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 121
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 60. i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing (continued)
Contact Name SDCKE1 SDCLK SDCLK_B SDQS0 SDQS1 SDQS2 SDQS3 SDWE_B SPL_SPR_PA27 SSI1_CLK_PC23 SSI1_FS_PC20 SSI1_RXDAT_PC21 SSI1_TXDAT_PC22 SSI2_CLK_GPT4_TIN_PC27 SSI2_FS_GPT5_TOUT_PC24 SSI2_RXDAT_GPT5_TIN_PC25 SSI2_TXDAT_GPT4_TOUT_PC26 SSI3_CLK_SLCDC2_CLK_PC31 SSI3_FS_SLCDC2_D0_PC28 SSI3_RXDAT_SLCDC2_RS_PC29 SSI3_TXDAT_SLCDC2_CS_PC30 SSI4_CLK_PC19 SSI4_FS_PC16 SSI4_RXDAT_PC17 SSI4_TXDAT_PC18 TCK TDI TDO TIN_PC15 TMS TOUT_PC14 TRST_B UART1_CTS_PE14 Location Y14 AD13 AD14 AD9 W8 W6 Y3 W13 B3 B9 F9 A9 E9 B10 G9 A10 F10 B11 E10 A11 C9 B8 F8 A8 G8 F17 B18 E16 B7 B19 E8 C17 A18
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 122 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 60. i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing (continued)
Contact Name UART1_RTS_PE15 UART1_RXD_PE13 UART1_TXD_PE12 UART2_CTS_KP_COL7_PE3 UART2_RTS_KP_ROW7_PE4 UART2_RXD_KP_ROW6_PE7 UART2_TXD_KP_COL6_PE6 UART3_CTS_PE10 UART3_RTS_PE11 UART3_RXD_PE9 UART3_TXD_PE8 UPLLVDD UPLLVSS USB_OC_B_PB24 USB_PWR_PB23 USBH1_FS_UART4_RTS_PB26 USBH1_OE_B_PB27 USBH1_RCV_PB25 USBH1_RXDM_PB30 USBH1_RXDP_UART4_RXD_PB31 USBH1_SUSP_PB22 USBH1_TXDM_UART4_TXD_PB28 USBH1_TXDP_UART4_CTS_PB29 USBH2_CLK_PA0 USBH2_DATA7_PA2 USBH2_DIR_PA1 USBH2_NXT_PA3 USBH2_STP_PA4 USBOTG_CLK_PE24 USBOTG_DATA0_PC9 USBOTG_DATA1_PC11 USBOTG_DATA2_PC10 USBOTG_DATA3_PC13 Location C16 F16 B17 E12 A14 E14 A16 A17 E15 F15 B16 J18 M15 H20 F23 E19 C24 H22 J20 E24 G19 F19 D24 H23 J24 K23 L20 J23 K24 J19 G18 G23 K20
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 123
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 60. i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing (continued)
Contact Name USBOTG_DATA4_PC12 USBOTG_DATA5_PC7 USBOTG_DATA6_PC8 USBOTG_DATA7_PE25 USBOTG_DIR_KP_ROW7A_PE2 USBOTG_NXT_KP_COL6A_PE0 USBOTG_STP_KP_ROW6A_PE1 VSYNC_PA29 XTAL26M XTAL32K Location H24 H19 G24 M22 N20 M20 L23 F5 AA24 N24
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 124 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
5.3
Freescale Semiconductor
Full Package Outline Drawing (19 mm x 19 mm)
Figure 69 shows the package drawings and dimensions of the production package.
Figure 69. i.MX27/MX27L 19 x 19 mm Full Package MAPBGA: Mechanical Drawing
i.MX27 and i.MX27L Data Sheet, Rev. 1.5
Package Information and Pinout
125
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
5.4
Pin Assignments (19 mm x 19 mm)
Table 61 shows the i.MX27 full 19 x 19 mm package MAPBGA pin assignment. Table 62 identifies the pin assignments for the ball grid array (BGA) for full package. The connections of these pins depend solely upon the user application, however there are a few factory test signals that are not used in a normal application. Following is a list of these signals and how they are to be terminated for proper operation of the i.MX27/MX27L processor: * CLKMODE[1:0]: To ensure proper operation, leave these signals as no connects. * OSC26M_TEST: To ensure proper operation, leave this signal as no connect. * EXT_60M: To ensure proper operation, connect this signal to ground. * EXT_266M: To ensure proper operation, connect this signal to ground. * Most of the signals shown in Table 62 are multiplexed with other signals. For ease of reference, all of the signals at a particular pad are shown in the form of a compound signal name. Refer to Table 3 for complete information on the signal multiplexing schemes of these signals.
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 126 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
23 23
GND CSPI2_SS0_USBH2 _DATA6_PD21 CSPI2_SS1_USBH2 _DATA3_PD20 CSPI1_SS1 _PD27 CSPI1_MOSI _PD31 SD1_CLK_CSPI3_ SCLK_PE23 CSPI1_SCLK _PD29 SD1_D3_CSPI3 _SS_PE21 CSPI1_SS2_USBH2 _DATA5_PD26 CSPI2_MISO_ USBH2_DATA2_PD23 CSPI2_SS2_USBH2 _DATA4_PD19 USB_PWR_ PB23 CSPI2_SCLK_USBH2 _DATA0_PD22 USB_OC_B _PB24 GND USBH1_RCV _PB25 CSPI2_MOSI_USBH2 _DATA1_PD24
22
CSPI1_MISO _PD30 SD1_CMD_CSPI3 _MOSI_PE22 CSPI1_RDY _PD25
CSPI1_SS0 _PD28
21
20
19
RTCK_OWIRE _PE16 UART1_RXD _PE13 UART1_RTS_ PE15 UART3_RTS_ PE11 UART2_RXD_KP_ ROW6_PE7 UART1_TXD_PE12 UART3_TXD _PE8 KP_COL4 KP_COL5 UART3_CTS _PE10 UART1_CTS _PE14
SD1_D0_CSPI3 _MISO_PE18
18
Table 61. i.MX27 Full 19 mm x 19 mm package MAPBGA Pin Assignment
17
16
15
14
UART2_CTS_KP _COL7_PE3 UART2_RTS_KP_ ROW7_PE4 KP_ROW4 KP_ROW5 KP_ROW3 KP_ROW2
I2C_CLK_ PD18
13
12
SSI3_CLK_SLCDC2 SSI3_RXDAT_SLCDC2 SSI3_TXDAT_SLCDC2_ _RS_PC29 _CLK_PC31 CS_PC30 SSI3_FS_SLCDC2 _D0_PC28 SSI2_FS_GPT5_TOUT _PC24 SSI1_FS_PC20 SSI1_CLK_ PC23 SSI4_CLK_ PC19 TIN_PC15 TOUT_PC14 CSI_HSYNC_UART5 _RTS_PB21 CSI_PIXCLK _PB16 CSI_D2_UART6_ CTS_PB12 SD2_CMD_MSHC _BS_PB8 SD2_D1_MSHC_ DATA1_PB5 GND CSI_D7_UART5_ RXD_PB19 CSI_D4_PB14 SSI4_RXDAT _PC17 SSI1_TXDAT _PC22 SSI2_RXDAT_GPT5 _TIN_PC25 SSI2_CLK_GPT4_ TIN_PC27 SSI1_RXDAT _PC21 SSI4_FS_PC16
11
10
9
8
CSI_D6_UART5 _TXD_PB18 CSI_D3_UART6 _RTS_PB13
7
CSI_D5_PB17
6
CSI_MCLK _PB15 CSI_D1_UART6 _RXD_PB11 SD2_D3_MSHC _DATA3_PB7 GND
CSI_D0_UART6_ TXD_PB10 SD2_D2_MSHC_ DATA2_PB6 OE_ACD_ PA31 CONTRAST _PA30
SD2_CLK_MSHC _SCLK_PB9 VSYNC_PA29 CLS_PA25
5
4
SPL_SPR_PA27
LD17_PA23
3
PS_PA26
LD16_PA22
2
GND
GND
SD2_D0_MSHC_ DATA0_PB4
HSYNC_PA28
LD15_PA21
1
C
D
A
B
i.MX27/i.MX27L Block Guide, Rev. 1.5 Freescale Semiconductor 127
E
1
2
3
4
5
6
7
8
9
10
11
KP_ROW1
12
13
KP_COL0
14
PWMO_PE5 KP_COL3
KP_COL2
UART2_TXD_KP_ COL6_PE6
15
16
TDO
17
TDI
18
TMS
19
SD1_D1_PE19
SD1_D2_PE20
20
21
22
GND
GND
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
USBH1_TXDP_ UART4_CTS_PB29 USBH2_CLK _PA0 USBOTG_STP_KP _ROW6A_PE1 USBH2_NXT _PA3 USBH2_DATA7 _PA2 USBOTG_NXT_KP _COL6A_PE0 USBOTG_DATA7 _PE25 USBH2_DIR _PA1 USBH1_TXDM_ UART4_TXD_PB28 USBH1_OE_B _PB27 USBH1_FS_UART4 _RTS_PB26 USBH1_RXDM _PB30 USBOTG_DATA5 USBOTG_DATA1 _PC7 _PC11 USBH1_RXDP_ USBOTG_DATA6 USBOTG_DATA4 UART4_RXD_PB31 _PC8 _PC12
23
22
21
20
19
Table 61. i.MX27 Full 19 mm x 19 mm package MAPBGA Pin Assignment (continued)
18
17
16
15
UART3_RXD _PE9 KP_COL1 GND NVDD9 QVDD GND GND
14
13
I2C_DATA_ PD17 GND KP_ROW0 GND NVDD10 QVDD GND
12
11
SSI2_TXDAT_GPT4_ TOUT_PC26 GND SSI4_TXDAT_ PC18 GND CSI_VSYNC_UART5 _CTS_PB20 GND GND QVDD NVDD11 QVDD QVDD NVDD11 QVDD
10
GND
GND
9
QVDD
QVDD
8
NVDD12
NVDD1
NVDD1
7
GND
NVDD15
NVDD15
NVDD12
NVDD1
NVDD1
6
5
REV_PA24
LD11_PA17
LD9_PA15
LD4_PA10
LSCLK_PA5
NFCLE_ ETMTRACEPKT0_PF1 LD6_PA12 LD2_PA8 NFCE_B_ ETMTRACEPKT2_PF3 NFRE_B_ ETMPIPESTAT1_PF5
4
LD14_PA20
LD10_PA16
3
LD12_PA18
LD7_PA13
LD5_PA11
LD1_PA7
NFRB_ ETMTRACEPKT3_PF0 LD8_PA14 LD3_PA9 LD0_PA6 NFWP_B_ ETMTRACEPKT1_PF2
NFALE_ ETMPIPESTAT0_PF4 NFWE_B_ ETMPIPESTAT2_PF6
2
LD13_PA19
1
G
H
K
F
i.MX27/i.MX27L Block Guide, Rev. 1.5 128 Freescale Semiconductor
L
J
1
2
3
4
5
6
7
8
9
10
NVDD11 QVDD
GND
GND
11
GND
12
NVDD10 QVDD GND
GND
13
14
NVDD9 QVDD GND GND GND
15
TCK
NVDD8 QVDD GND GND GND
16
TRST_B QVDD QVDD
NVDD8 QVDD QVDD
17
QVDD NVDD14 UPLLVSS
QVDD QVDD UPLLVDD
18
GND NVDD7 NVDD13
USBH1_SUSP _PB22 NVDD14 NVDD7
19
20
21
22
I2C2_SDA_PC5 USBOTG_DATA0 USBOTG_DATA3 _PC9 _PC13 USBOTG_CLK_PE24
23
I2C2_SCL_PC6 USBOTG_DATA2 _PC10 USBH2_STP _PA4
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
23 23
POWER_CUT EXTAL32K XTAL32K ATA_DATA2 _SD3_D2_PD4 ATA_DATA6_ FEC_MDIO_PD8 ATA_DATA7_ ETMTRACEPKT12_PD9 ATA_DATA3 _SD3_D3_PD5 ATA_DATA4_ ATA_DATA9_ ETMTRACEPKT14_PD6 ETMTRACEPKT10_PD11 ATA_DATA5_ ATA_DATA8_ ETMTRACEPKT13_PD7 ETMTRACEPKT11_PD10
POWER_ON_ RESET OSC32K_ BYPASS USBOTG_DIR_KP _ROW7A_PE2 SD3_CMD_ PD0 ATA_DATA0_SD3 _D0_PD2
22
21
20
19
Table 61. i.MX27 Full 19 mm x 19 mm package MAPBGA Pin Assignment (continued)
18
17
16
15
14
13
12
11
10
GND GND
GND
GND
QVDD
9
QVDD QVDD
QVDD
QVDD
QVDD
8
QVDD D0
NVDD2
NVDD2
NVDD2
7
D11 D7
MA10
NVDD2
A1
6
5
D13 D8
NC_P4_1
A12
A7
4
D12 D5
D3
A13
A8
3
D14
D9
D4
D1
A9
2
D15
D10
D6
D2
A11
1
M
N
R
P
i.MX27/i.MX27L Block Guide, Rev. 1.5 Freescale Semiconductor 129
T
1
2
3
4
5
6
7
8
9
10
GND GND
GND
GND
QVDD
11
GND GND
GND
GND
QVDD
12
GND GND
GND
GND QVDD
13
GND GND
GND
GND QVDD
14
GND
GND GND QVDD
GND
15
GND
GND GND QVDD
GND
16
QVDD QVDD
QVDD
QVDD QVDD
17
RTCVSS FPMVSS
NVDD6
FUSEVSS MPLLVSS
18
RTCVDD FPMVDD
NVDD6
FUSEVDD BOOT2
19
20
21
OSC32VDD
ATA_DATA1_SD3 _D1_PD3
22
OSC32VSS
SD3_CLK_ ETMTRACEPKT15_PD1
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
ATA_DATA10_ ATA_DATA14_ETM ETMTRACEPKT9_PD12 TRACEPKT5_PD16 ATA_DATA11_ ETMTRACEPKT8_PD13 ATA_DATA15_ETM OSC26VDD TRACEPKT4_PF23 ATA_DATA12_ ETMTRACEPKT7_PD14 ATA_DATA13_ ETMTRACEPKT6_PD15 PC_RST_ATA_ RESET_B_PF10 PC_BVD1_ATA _DMARQ_PF12 PC_WAIT_B _ATA_CS1_PF18
23
22
21
20
19
Table 61. i.MX27 Full 19 mm x 19 mm package MAPBGA Pin Assignment (continued)
18
17
16
15
14
13
12
11
10
NVDD2 SD12 SD9
SD7
9
NVDD2
GND
SD13
SD11
8
NVDD2
GND
A19
SD15
7
SD29
A22
SD17
SD16
6
SD20
A20
5
A3
SD31
SD27
SD26
SD22
4
A4
SDBA0
SDQS3
SD28
SD24
3
A5
A0
A25
A24
A23
2
A6
A2
SDBA1
SD30
SD25
1
i.MX27/i.MX27L Block Guide, Rev. 1.5 130 Freescale Semiconductor
AA
W
U
V
Y
1
2
3
4
5
6
7
8
9
10
QVDD SD6 SDQS0
A15
11
NVDD3 SD2 DQM3 SD0
12
NVDD3 DQM1 RAS_B DQM0
13
SDCKE1 SDCKE0 SDCLK_B SDCLK
14
NVDD4 CS5_B_ETM TRACECLK_PF22 CS4_B_ETMTRACE SYNC_PF21 RW_B
15
NVDD4 NVDD5 CS0_B
CS1_B
16
NVDD4 NVDD5 OE_B EB0_B
17
AVDD MPLLVDD PC_CD2_B_ATA_ DIOW_PF19 EXT_60M
18
AVSS GND PC_VS1_ATA_ DA1_PF14
19
20
BOOT1
OSC26M _TEST PC_POE_ATA_ BUFFER_EN_PF7
IOIS16_ATA_ INTRQ_PF9
21
BOOT0
OSC26VSS POR_B
RESET_IN_B
22
CLKMODE1
CLKMODE0
23
BOOT3 EXTAL26M
XTAL26M
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Table 61. i.MX27 Full 19 mm x 19 mm package MAPBGA Pin Assignment (continued)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
JTAG_CTRL
Freescale Semiconductor i.MX27/i.MX27L Block Guide, Rev. 1.5 131
18
PC_CD1_B_ATA _DIOR_PF20
19
PC_PWRON_ATA_ PC_READY_ DA2_PF16 ATA_CS0_PF17
20
PC_BVD2_ATA_ DMACK_PF11
21
PC_RW_B_ATA _IORDY_PF8
22
23
SDWE_B
SDQS2
SDQS1
ECB_B
CS2_B
EB1_B
SD21
SD19
SD14
SD10
GND
GND
GND
GND
SD5
SD4
SD1
A10
AB
PC_VS2_ATA_ DA0_PF13
RESET_OUT_ B_PE17
CLKO_PF15
EXT_266M
CAS_B
CS3_B
LBA_B
DQM2
BCLK
SD23
SD18
GND
GND
GND
GND
SD8
SD3
A21
A18
A17
A16
A14
AC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Package Information and Pinout
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62 shows the device pin list, sorted by sorted by location.
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing
Contact Name A0 A1 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A2 A20 A21 A22 A23 A24 A25 A3 A4 A5 A6 A7 A8 A9 ATA_DATA0_SD3_D0_PD2 ATA_DATA1_SD3_D1_PD3 ATA_DATA10_ETMTRACEPKT9_PD12 ATA_DATA11_ETMTRACEPKT8_PD13 ATA_DATA12_ETMTRACEPKT7_PD14 ATA_DATA13_ETMTRACEPKT6_PD15 Location V2 T6 AB12 T1 R4 R3 AC10 AA10 AC9 AC7 AC6 Y7 V1 AA5 AC4 V6 AA2 Y2 W2 U4 U3 U2 U1 T4 T3 T2 P20 P21 U23 U22 U21 U20
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 132 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name ATA_DATA14_ETMTRACEPKT5_PD16 ATA_DATA15_ETMTRACEPKT4_PF23 ATA_DATA2_SD3_D2_PD4 ATA_DATA3_SD3_D3_PD5 ATA_DATA4_ETMTRACEPKT14_PD6 ATA_DATA5_ETMTRACEPKT13_PD7 ATA_DATA6_FEC_MDIO_PD8 ATA_DATA7_ETMTRACEPKT12_PD9 ATA_DATA8_ETMTRACEPKT11_PD10 ATA_DATA9_ETMTRACEPKT10_PD11 AVDD AVSS BCLK BOOT0 BOOT1 BOOT2 BOOT3 CAS_B CLKMODE0 CLKMODE1 CLKO_PF15 CLS_PA25 CONTRAST_PA30 CS0_B CS1_B CS2_B CS3_B CS4_B_ETMTRACESYNC_PF21 CS5_B_ETMTRACECLK_PF22 CSI_D0_UART6_TXD_PB10 CSI_D1_UART6_RXD_PB11 CSI_D2_UART6_CTS_PB12 CSI_D3_UART6_RTS_PB13 Location V23 V22 R23 R22 R21 R20 T23 T22 T20 T21 U17 U18 AC16 V21 V20 T18 W23 AC13 AA22 Y22 AC17 E4 C2 Y15 AA15 AB14 AC14 Y14 V14 C5 A4 B5 D6
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 133
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name CSI_D4_PB14 CSI_D5_PB17 CSI_D6_UART5_TXD_PB18 CSI_D7_UART5_RXD_PB19 CSI_HSYNC_UART5_RTS_PB21 CSI_MCLK_PB15 CSI_PIXCLK_PB16 CSI_VSYNC_UART5_CTS_PB20 CSPI1_MISO_PD30 CSPI1_MOSI_PD31 CSPI1_RDY_PD25 CSPI1_SCLK_PD29 CSPI1_SS0_PD28 CSPI1_SS1_PD27 CSPI1_SS2_USBH2_DATA5_PD26 CSPI2_MISO_USBH2_DATA2_PD23 CSPI2_MOSI_USBH2_DATA1_PD24 CSPI2_SCLK_USBH2_DATA0_PD22 CSPI2_SS0_USBH2_DATA6_PD21 CSPI2_SS1_USBH2_DATA3_PD20 CSPI2_SS2_USBH2_DATA4_PD19 D0 D1 D10 D11 D12 D13 D14 D15 D2 D3 D4 D5 Location C6 A6 D7 C7 B7 A5 B6 F8 A21 C20 B20 D19 B21 C21 D20 E20 D23 D22 C23 C22 D21 N7 R2 N1 M6 M3 M4 M2 M1 R1 P3 P2 N3
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 134 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name D6 D7 D8 D9 DQM0 DQM1 DQM2 DQM3 EB0_B EB1_B ECB_B EXT_266M EXT_60M EXTAL26M EXTAL32K FPMVDD FPMVSS FUSEVDD FUSEVSS GND GND GND GND GND GND GND GND GND GND GND GND GND GND Location P1 N6 N4 N2 AA12 V12 AC12 Y11 AA16 AB16 AB15 AC18 AA17 Y23 N23 N18 N17 R18 R17 A1 A2 A22 A23 AB1 AB2 AB22 AB23 AC1 AC2 AC22 AC23 B1 B2
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 135
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Location B22 B23 F6 F7 F18 G7 J9 J10 J11 J12 J13 J14 J15 K9 K10 K11 K12 K13 K14 K15 L9 L10 L11 L12 L13 L14 L15 M9 M10 M11 M12 M13 M14
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 136 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND HSYNC_PA28 I2C_CLK_PD18 I2C_DATA_PD17 I2C2_SCL_PC6 I2C2_SDA_PC5 IOIS16_ATA_INTRQ_PF9 JTAG_CTRL KP_COL0 Location M15 N9 N10 N11 N12 N13 N14 N15 P9 P10 P11 P12 P13 P14 P15 R9 R10 R11 R12 R13 R14 R15 V7 V8 V18 D1 B13 F12 G23 G22 AA20 AB17 D13
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 137
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name KP_COL1 KP_COL2 KP_COL3 KP_COL4 KP_COL5 KP_ROW0 KP_ROW1 KP_ROW2 KP_ROW3 KP_ROW4 KP_ROW5 LBA_B LD0_PA6 LD1_PA7 LD10_PA16 LD11_PA17 LD12_PA18 LD13_PA19 LD14_PA20 LD15_PA21 LD16_PA22 LD17_PA23 LD2_PA8 LD3_PA9 LD4_PA10 LD5_PA11 LD6_PA12 LD7_PA13 LD8_PA14 LD9_PA15 LSCLK_PA5 MA10 MPLLVDD Location F13 B14 C14 A15 B15 F11 D11 B12 A12 C12 D12 AC15 J1 J2 G3 G4 F2 F1 F3 E1 E2 E3 J3 H1 J4 H2 H3 G2 G1 H4 K4 P6 V17
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 138 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name MPLLVSS NC_P4_1 NFALE_ETMPIPESTAT0_PF4 NFCE_B_ETMTRACEPKT2_PF3 NFCLE_ETMTRACEPKT0_PF1 NFRB_ETMTRACEPKT3_PF0 NFRE_B_ETMPIPESTAT1_PF5 NFWE_B_ETMPIPESTAT2_PF6 NFWP_B_ETMTRACEPKT1_PF2 NVDD1 NVDD1 NVDD1 NVDD1 NVDD10 NVDD10 NVDD11 NVDD11 NVDD11 NVDD12 NVDD12 NVDD13 NVDD14 NVDD14 NVDD15 NVDD15 NVDD2 NVDD2 NVDD2 NVDD2 NVDD2 NVDD2 NVDD2 NVDD3 Location T17 P4 L2 K3 L4 K2 L3 L1 K1 K6 K7 L6 L7 G11 G12 G8 G9 G10 J6 J7 L18 H18 J17 G6 H6 P7 R6 R7 T7 U7 U8 U9 U11
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 139
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name NVDD3 NVDD4 NVDD4 NVDD4 NVDD5 NVDD5 NVDD6 NVDD6 NVDD7 NVDD7 NVDD8 NVDD8 NVDD9 NVDD9 OE_ACD_PA31 OE_B OSC26M_TEST OSC26VDD OSC26VSS OSC32K_BYPASS OSC32VDD OSC32VSS PC_BVD1_ATA_DMARQ_PF12 PC_BVD2_ATA_DMACK_PF11 PC_CD1_B_ATA_DIOR_PF20 PC_CD2_B_ATA_DIOW_PF19 PC_POE_ATA_BUFFER_EN_PF7 PC_PWRON_ATA_DA2_PF16 PC_READY_ATA_CS0_PF17 PC_RST_ATA_RESET_B_PF10 PC_RW_B_ATA_IORDY_PF8 PC_VS1_ATA_DA1_PF14 PC_VS2_ATA_DA0_PF13 Location U12 U14 U15 U16 V15 V16 P17 P18 J18 K18 G15 G16 G13 G14 C3 Y16 W20 W22 W21 M21 N21 N22 AA19 AB20 AB18 Y17 Y20 AC19 AB19 Y19 AB21 Y18 AC20
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 140 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name PC_WAIT_B_ATA_CS1_PF18 POR_B POWER_CUT POWER_ON_RESET PS_PA26 PWMO_PE5 QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD Location AA18 Y21 M23 M22 D2 A14 F17 G17 H7 H8 H9 H10 H11 H12 H13 H14 H15 H16 H17 J8 J16 K8 K16 L8 L16 M7 M8 M16 N8 N16 P8 P16 R8
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 141
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD QVDD RAS_B RESET_IN_B RESET_OUT_B_PE17 REV_PA24 RTCK_OWIRE_PE16 RTCVDD RTCVSS RW_B SD0 SD1 SD1_CLK_CSPI3_SCLK_PE23 SD1_CMD_CSPI3_MOSI_PE22 SD1_D0_CSPI3_MISO_PE18 SD1_D1_PE19 SD1_D2_PE20 SD1_D3_CSPI3_SS_PE21 SD10 SD11 SD12 SD13 SD14 SD15 Location R16 T8 T9 T10 T11 T12 T13 T14 T15 T16 U10 Y12 AA21 AC21 F4 A18 M18 M17 AA14 AA11 AB11 C19 A20 B18 A19 B19 D18 AB8 AA8 V9 Y8 AB7 AA7
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 142 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name SD16 SD17 SD18 SD19 SD2 SD2_CLK_MSHC_SCLK_PB9 SD2_CMD_MSHC_BS_PB8 SD2_D0_MSHC_DATA0_PB4 SD2_D1_MSHC_DATA1_PB5 SD2_D2_MSHC_DATA2_PB6 SD2_D3_MSHC_DATA3_PB7 SD20 SD21 SD22 SD23 SD24 SD25 SD26 SD27 SD28 SD29 SD3 SD3_CLK_ETMTRACEPKT15_PD1 SD3_CMD_PD0 SD30 SD31 SD4 SD5 SD6 SD7 SD8 SD9 SDBA0 Location AA6 Y6 AC5 AB5 V11 D5 B4 C1 B3 C4 A3 Y5 AB4 AA4 AC3 AA3 AA1 Y4 W4 Y3 U6 AC11 P22 N20 Y1 V4 AB10 AB9 V10 AA9 AC8 Y9 V3
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 143
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name SDBA1 SDCKE0 SDCKE1 SDCLK SDCLK_B SDQS0 SDQS1 SDQS2 SDQS3 SDWE_B SPL_SPR_PA27 SSI1_CLK_PC23 SSI1_FS_PC20 SSI1_RXDAT_PC21 SSI1_TXDAT_PC22 SSI2_CLK_GPT4_TIN_PC27 SSI2_FS_GPT5_TOUT_PC24 SSI2_RXDAT_GPT5_TIN_PC25 SSI2_TXDAT_GPT4_TOUT_PC26 SSI3_CLK_SLCDC2_CLK_PC31 SSI3_FS_SLCDC2_D0_PC28 SSI3_RXDAT_SLCDC2_RS_PC29 SSI3_TXDAT_SLCDC2_CS_PC30 SSI4_CLK_PC19 SSI4_FS_PC16 SSI4_RXDAT_PC17 SSI4_TXDAT_PC18 TCK TDI TDO TIN_PC15 TMS TOUT_PC14 Location W1 V13 U13 AA13 Y13 Y10 AB6 AB3 W3 AB13 D3 A9 C9 D9 B9 D10 C10 B10 F10 A11 A10 B11 C11 A8 D8 B8 F9 F15 D17 D16 C8 C18 A7
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 144 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name TRST_B UART1_CTS_PE14 UART1_RTS_PE15 UART1_RXD_PE13 UART1_TXD_PE12 UART2_CTS_KP_COL7_PE3 UART2_RTS_KP_ROW7_PE4 UART2_RXD_KP_ROW6_PE7 UART2_TXD_KP_COL6_PE6 UART3_CTS_PE10 UART3_RTS_PE11 UART3_RXD_PE9 UART3_TXD_PE8 UPLLVDD UPLLVSS USB_OC_B_PB24 USB_PWR_PB23 USBH1_FS_UART4_RTS_PB26 USBH1_OE_B_PB27 USBH1_RCV_PB25 USBH1_RXDM_PB30 USBH1_RXDP_UART4_RXD_PB31 USBH1_SUSP_PB22 USBH1_TXDM_UART4_TXD_PB28 USBH1_TXDP_UART4_CTS_PB29 USBH2_CLK_PA0 USBH2_DATA7_PA2 USBH2_DIR_PA1 USBH2_NXT_PA3 USBH2_STP_PA4 USBOTG_CLK_PE24 USBOTG_DATA0_PC9 USBOTG_DATA1_PC11 Location F16 B17 C17 A17 D15 A13 C13 C15 D14 B16 C16 F14 A16 K17 L17 E22 E21 F20 F21 E23 G20 G21 G18 F22 F23 J23 K21 K20 K22 K23 L22 H22 J20
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 145
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Package Information and Pinout
Table 62. i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing (continued)
Contact Name USBOTG_DATA2_PC10 USBOTG_DATA3_PC13 USBOTG_DATA4_PC12 USBOTG_DATA5_PC7 USBOTG_DATA6_PC8 USBOTG_DATA7_PE25 USBOTG_DIR_KP_ROW7A_PE2 USBOTG_NXT_KP_COL6A_PE0 USBOTG_STP_KP_ROW6A_PE1 VSYNC_PA29 XTAL26M XTAL32K Location H23 J22 J21 H20 H21 L20 M20 L21 L23 D4 AA23 P23
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 146 Freescale Semiconductor
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
Product Documentation
6
Product Documentation
This Data Sheet is labeled as a particular type: Product Preview, Advance Information, or Technical Data. Definitions of these types are available at: http://www.freescale.com.
7
Revision History
Table 63. Document Revision History
Rev. No. 1.5 1.4 Date 12/2009 5/2009 Significant Change(s) * Updated Table 1, "Ordering Information," to include new part numbers and table footnote. * In Table 11 Current Consumption a column for Max value was added. * In Table 59, "i.MX27 Full 17 x 17 mm Package MAPBGA Pin Assignment," inaccurate pin list information was corrected and the table reformatted. * In Table 60, "i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing," inaccurate pin list information was corrected and the table was reformatted. * Reformatted Table 62, "i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing." * In Table 3, "i.MX27/MX27L Signal Descriptions," switched FEC_TXD0 and FEC_TXD1 for SD3_CMD and SD3_CLK. * In Table 23, "CSPI Interface Timing Parameters," updated t6' and t13, and removed t14. * In Table 60, "i.MX27 BGA (17 mm x 17 mm)-- Contact Name Listing," changed "RW" to "RW_B." * Added Table 59, "i.MX27 Full 17 x 17 mm Package MAPBGA Pin Assignment." * Updated Table 62, "i.MX27 BGA (19 mm x 19 mm)--Contact Name Listing." Corrected part number in section 1.3, "Ordering Information," on p. 4. Part number previously listed as MCIMX27FVOP4A has been corrected to read MCIMX27VOP4A. Formatting and template work.
Table 63 summarizes revisions to this document since the previous release.
1.3
11/2008
1.2 1.1
7/2008 7/2008
i.MX27 and i.MX27L Data Sheet, Rev. 1.5 Freescale Semiconductor 147
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A
How to Reach Us:
Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800 441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 LDCForFreescaleSemiconductor @hibbertgroup.com
Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics as their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale's Environmental Products program, go to http://www.freescale.com/epp.
Freescale are trademarks or registered trademarks of Freescale Semiconductor, Inc. in the U.S. and other countries. ARM is the registered trademark of ARM Limited. ARM926EJ-S is a trademark of ARM Limited. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc., 2009. All rights reserved.
Document Number: MCIMX27EC Rev. 1.5 12/2009
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010: MCIMX27VOP4A, MCIMX27LVOP4A, MCIMX27MOP4A, MCIMX27LMOP4A

▲Up To Search▲

Price & Availability of IMX27

	To Download IMX27 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .